Jump to content
SAU Community

Recommended Posts

Where can i buy half decent wheel spacers from? Ive been through 2 sets from just jap and had nothing but trouble with them ie; shaking steering.

Mate at work said qtr are good? Googled them but nothing came up.

Cheers.

Have you been using hubcentric spacers?

These have a lip in the centre to locate the hub of the rim so all the weight of the car is not being supported on the wheel studs. If not, you'll find it's almost impossible to get rid of the shake, as the wheels are not on centre. Also the lip must engage firmly both on the disc hub, And the wheel hub.

When you had issues, did you return the to Just Jap for replacement?

I've used hubcentric spacers a few times and provided they're machined correctly you should have no issues. (Even though spacers are illegal and the correct offset wheel is always the best solution)

I've used

Yea returned some 30mm and got some 20mm but still the same issues. I know 100% its not the wheels as when i ran a 5mm slip on it was perfectly steady at 100 and above plus the wheels are new.

Im pretty damn sure they had the ring on the spacer but the hole on the drift teks is pretty big and it doesnt sit tight on it.

Can anyone recommend a place to get high quality spacers from?

can't blame the spacers for the wheel shake if the center bore of the wheel is larger than the ring on the spacer. that's what's supposed to center the wheel so you don't get the shakes.

fwiw, the hub ring doesn't take any load, it just centers the wheel while you tighten it. friction between the wheel and hub takes the load.

Edited by hrd-hr30

While i do agree somewhat with that its not like on some wheels were the wheel can move al over the before the nuts are tightened. With the wheel sitting on the spacer it sits on there pretty tight and doesnt feel like it can move anywhere especially when tightened.

I will try it though, will go a tyre place tonight and see if they have any.

+1 for hubcentric rings

While i do agree somewhat with that its not like on some wheels were the wheel can move al over the before the nuts are tightened. With the wheel sitting on the spacer it sits on there pretty tight and doesnt feel like it can move anywhere especially when tightened.

I will try it though, will go a tyre place tonight and see if they have any.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...