Jump to content
SAU Community

Recommended Posts

Up for sale is a set of R33 GTR sway bars.

I bought these off bubba a while back and they don't fit my car(Auto)

They will fit manual C34 series 1 or 2 stagea.

(please dont turn this into an argument about what swaybars fit what car)

the rear is 22 or 24mm solid from memory, a great upgrade over the standard 17mm hollow bar.

Selling them for less than i paid for them.

Rear sway bar comes with rubbers, u bolts and links to suit.

$150 + postage

Located south of Adelaide

Pm or call me - 0423 10 11 10

stock rear sway bar compared to r33GTR sway bar

DSC01091.jpg

They will fit manual C34 series 1 or 2 stagea.

(please dont turn this into an argument about what swaybars fit what car)

Firstly I'm genuinely interested in this item.... However Im unsure as to if these will fit my car, why doesn't it fit your auto? Whats different from the auto and manual rear sway bars.

Also for the record RS4's were NEVER sold in a manual.

Firstly I'm genuinely interested in this item.... However Im unsure as to if these will fit my car, why doesn't it fit your auto? Whats different from the auto and manual rear sway bars.

Also for the record RS4's were NEVER sold in a manual.

it's all about that rear cradle and the extra width that the autos have. i have heard of people putting the sway bar links on mad angles and this didn't really worry me but on my car i couldn't get the u bolts in.

When i bolt one side on, the other side was a full bolt hole off, if you were to bolt them up like this, the rubbers would be sitting on the corners of the sway bar, not the straight section.

Anyone is more than welcome to come and put there car on my hoist and have a look, if you think you can make it work and deal with the link angles, you are more than welcome to buy them

p.s whats with the random rs4 fact??

Edited by Big Fella

looking at my mates rs4s his rear sway bar was only 19mm, so it would be an upgrade for sure.

Just measured the 33 gtr sway bars

front is 22mm solid

rear is 27mm solid

here is the issue for auto stageas, the right side is bolted up and the lsft hand side is way off.

the right side is shwon here, right on the edge of the straight section

DSC01187.jpg

and this is how far off the left side is

DSC01188.jpg

i was planning to make a 5mm thick plate for each side, with 2 threaded holes and thru holes to mount it up, but i've run out of time and motivation

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...