Jump to content
SAU Community

Recommended Posts

  • Replies 224
  • Created
  • Last Reply

Top Posters In This Topic

OK Everyone, how's this sound:

 

1. All southside/GC people meet at Springwood crazy clarks at 7:30pm for departure at 8pm sharp

 

2. Cruise up to New Shell just north of the Gateway bridge on the highway, meet all you brissie ppl there say 8:30pm?

 

Havent quite firgured out where to go after that, but then again, I'm just making this up as I go alone, with some help from others, strutto and hopefully you........

roma is not gonna be big enough to accommodate all of us... there will be many other cars as well and not to forget the fact that the cops have increased their patrol of the area. Milton Maccas is a no-go as well. i reckon that Ska's suggestion is probably the best unless there's a better place to meet in Brisbane.

where is the New Shell anyway?

ok... so its settled.

Brisbane ppl - meet at Milton Maccas at 7.30pm and we leave at 7.45pm sharp. I will tell Yoparata to meet at 7.15pm cos he's always 20 mins late (got the hint yet, Aaron? :P)

cruise up to the New Shell, meet up with the rest of the group, have a chat and decide what to do from there.

onz?

glenn

I will be up in brisbane on thurs nite (in my flat-mate's gti-r) and will be meeting with some redlineau people, most probably at albion maccas, but its not too far from this new shell. I will try and twist his arm to go for a quick run out there (if you dont mind a jnr zilla about :S )

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...