Jump to content
SAU Community

Recommended Posts

Hey guys,

I am selling a complete Nismo NE-1 Weldina exhaust system that is off an R33 GTR. It has had both cats pulled out and has been on a car making 340AWKW. Was removed to make way for a completely custom made exhaust system.

These are great as i have been pulled over with it before and just the fact that is has nismo on the exhaust tip believe it or not does seem to help cops believe that its a Nissan/Nismo semi legal part. It has deff helped me once before.

I can get photo's if required, but is in above average to good condition. rare to find these days as they are still a very nice exhaust system.

Located in SE suburbs of Melbourne but can organise freight Aus wide.

sms me on 0423-130-616

Price is $1000 firm and obviously freight at buyers expense.

Link to comment
https://www.sau.com.au/forums/topic/353512-nismo-ne-1-weldina-exhaust/
Share on other sites

Hey guys,

I am selling a complete Nismo NE-1 Weldina exhaust system that is off an R33 GTR. It has had both cats pulled out and has been on a car making 340AWKW. Was removed to make way for a completely custom made exhaust system.

These are great as i have been pulled over with it before and just the fact that is has nismo on the exhaust tip believe it or not does seem to help cops believe that its a Nissan/Nismo semi legal part. It has deff helped me once before.

I can get photo's if required, but is in above average to good condition. rare to find these days as they are still a very nice exhaust system.

Located in SE suburbs of Melbourne but can organise freight Aus wide.

sms me on 0423-130-616

Price is $1000 firm and obviously freight at buyers expense.

ok guys due to lack of interest i am negotiable on price, someone get a great exhaust here, genuine NISMO goodness!

beautiful, thanks for the info champ!!! i knew you could get them for 34 gtrs also but i was not sure if they were same model or not.

This system has 1 hanger trimmed off but its easily replaceable.

throw some offers around guys.

nah the cat "bodies" are still there so from the outside it looks un touched. yeah i will have to get some pics up as no one seems really interested atm. might have to ebay it.

nah the cat "bodies" are still there so from the outside it looks un touched. yeah i will have to get some pics up as no one seems really interested atm. might have to ebay it.

i'm interested just waiting for pics to see condition of rear end, also can you get the diameter of the pipes

Here is a couple photo's of the rear muffler, hard to really show it because i have too many lights in my room....

muffler is in great condition. rest of the zorst is usuall colourations to it, no dints or dings though.

post-59170-0-84423700-1297851226_thumb.jpg

post-59170-0-59606900-1297851319_thumb.jpg

Sorry for the late reply guys.

the front twin pipes are 60mm in diameter. hot dog o/d is 90mm. i know its diff unit measurement but i know the rear single section is single 3" straight through to tip.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...