Jump to content
SAU Community

Swapping Speedo's

R33 0wnerrr

By R33 0wnerrr,
in Exterior & Interior Styling

 Share

Recommended Posts

R33 0wnerrr Enthusiast

R33 0wnerrr

Posted
Posted

Hey guys,

Wasnt 100% sure if this is the right place to ask, BUT!

I am wanting to swap my r34 GTR speedo out for a 320km/h one my friend has, to use on a track day as I dont want to watch my 180 stock speedo go around in circles when i go past 180

But what I wanted to know is if I swap this speedo, use it, then replace it back with the stock one after the day, will this void the stock speedo's digital kms in any way?

Because if it does I wont bother swapping it just for a day...Just to try keep the kms on the odometer genuine if that all makes sense?

Thanks guys comments appreciated!

Link to comment
https://www.sau.com.au/forums/topic/354897-swapping-speedos/
Share on other sites
ecliptor Enthusiast

ecliptor

Posted
Posted

Hey guys,

Wasnt 100% sure if this is the right place to ask, BUT!

I am wanting to swap my r34 GTR speedo out for a 320km/h one my friend has, to use on a track day as I dont want to watch my 180 stock speedo go around in circles when i go past 180

But what I wanted to know is if I swap this speedo, use it, then replace it back with the stock one after the day, will this void the stock speedo's digital kms in any way?

Because if it does I wont bother swapping it just for a day...Just to try keep the kms on the odometer genuine if that all makes sense?

Thanks guys comments appreciated!

yes it will void the genuine kms, as the km's you use on the track will clock up on the 320km/h cluster and not the original

- for example say ur car has 54,000 kms on its original cluster and you do 20kms on the 320km/h cluster, when you replace the original it will still read 54,000km

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • funkymonkey
      Jacks that fit under GTR lips that can reach the subframe?

      By funkymonkey · Posted

      I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
×
×
  • Create New...