Jump to content
SAU Community

Oil Filter Relocation Kit Question...

neoRSwagon
 Share

Recommended Posts

neoRSwagon Apprentice

neoRSwagon

Posted
Posted

hey guys, just thinking about getting an oil filter relocation kit, one with out a cooler" , but when i install it, does it just screw onto the stock oil cooler? or do you have to remove it and block coolent lines or...?? as im sick of spending 45 mins getting the oil off the front diff. cheers

Link to comment
https://www.sau.com.au/forums/topic/357133-oil-filter-relocation-kit-question/
Share on other sites
pistol-pete Veteran

pistol-pete

Posted
Posted

the filter relocator kits dont change the way stock cooler is plumbed. you just screw the sandwich plate into the block and run the lines to the relocator which most people put on the rhs strut tower

QWK32 Veteran

QWK32

Posted
Posted (edited)

Put a Plastic bag over it :yes: ,

its not hard when you do that :thumbsup: ,

This method also works on ugly chicks.......

The plastic bag trick never worked for me, I still always ended up with oil all over the place. Oil filter relIcation kit makes it so much easier and cleaner.

Edited by QWK32
66yostagea Grand Master

66yostagea

Posted
Posted

Isent a PM but just realized that you cant PM yet. I relocated my filter to the D/S strut tower and moved the fuel filter back when fitting the F/F plenum and front mount. I also incorporated sensors in the lines for oil pressure and temperature gauges.

chuckie Mentor

chuckie

Posted
Posted

post-36964-0-21971300-1300087395_thumb.jpgpost-36964-0-64123400-1300089876_thumb.jpg

I have Relocation kit & kept stock filter too,

I PLASTIC BAG FILTER & put rag on top of diff & its ok no oil sitting there,

& i use New Fitler on Engine & move old filter to relocation,

as i run 20,000 per oil change & change filter at 10,000,

My Oil cooler has Thermostat in it,

best buy kits from states as most double there money on any kit brought here in Australia,

you can get adaptor with Thermostat in it ,

i priced a inline thermostat here & was quoted $120+,

got one from states for $45 usd,same price as TRANSMISSION FILTER KIT,

as you see both are in same spot ,

Run a good size oil line too,not a small line as you want good flow to any filter,

Cheer`s Chuckie.

SMOKEYV35 Mentor

SMOKEYV35

Posted
Posted

yeh if someone finds a good quality good priced kit to suit, let me know. i did my first change on it about a month ago and couldnt believe how tricky it was to get in there and then the mess ensued.

relocation kit would be awesome and allow you to run an even bigger filter if you wanted.

  • 1 month later...
WA Black Stag Rookie

WA Black Stag

Posted
Posted

Be careful with the Greddy kits - the lines on the one I got were way to short for the application. Do a check fit before you actually put it in, and go get some more line if you need it.

SABBAi Grand Master

SABBAi

Posted
Posted

This method also works on ugly chicks.......

The plastic bag trick never worked for me, I still always ended up with oil all over the place. Oil filter relIcation kit makes it so much easier and cleaner.

cable ties.... Make sure you fasten it with cable ties.

P.S. May stop breathing.

Hanso Experienced

Hanso

Posted
Posted

The lines on my Greddy kit were a bit short for my liking. I have bolted the bracket under the fuel filter bracket. Still nice & easy to get to.

Pics aren't the best, will take a better one on my day off.

P4190006.jpg

P4190008.jpg

P4190007.jpg

P4190009.jpg

WA Black Stag Rookie

WA Black Stag

Posted
Posted (edited)

The lines on my Greddy kit were a bit short for my liking. I have bolted the bracket under the fuel filter bracket. Still nice & easy to get to.

The only problem with this is it makes the dipstick a pain in the arse to get to. I initially did it this way, but got the shits, cause I check my oil daily.

Getting new hose (not braided, but then again, I'm not a bling king, and I'm not running stupid pressure through it) cost me $30, including the 4 hose clamps that i needed.

Edit: Noticed that you're using an OX-03 filter in there as well, the relocation kit is actually designed to take an OX-02, slightly bigger.

Edited by WA Black Stag
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • sunsetR33
      Unpeeling the Orange

      By sunsetR33 · Posted

      Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • wizlb
      Who has a Infiniti Q60, Q50 (V37)?

      By wizlb · Posted

      I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Kinkstaah
      Starting again

      By Kinkstaah · Posted

      Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...