Jump to content
SAU Community

Outer Northside Aspley To Caboolture

RandomHero83

By RandomHero83,
in Queensland

 Share

Recommended Posts

  • 3 weeks later...
  • Replies 3.5k
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

RandomHero83
RandomHero83

2 days off, 4 day weekend.

Cadmoon
Cadmoon

Ask chants about how coitus can fix joint problems

HiveFleetAbyss
HiveFleetAbyss

Mmmmm post count the indicator of which of use probably sit on the forum for too long and don't do any real work.

Posted Images

t5iv Grand Master

t5iv

Posted
Posted

My build is in progress :) bought a worked and complete head with all the goodies, dan from erd is going to build my engine, happy all round :)

Nicely done! That motor should be wicked after receiving the Dan touch.

mattis96 Proficient

mattis96

Posted
Posted

No I didn't buy it, rather spend the $2200 getting the engine finished first. And after seeing the 6266 result on the 26 engine punch out 500 rwkw or what ever it was I'm deciding between different turbos again

SCR48 Grand Master

SCR48

Posted
Posted

it will be interesting to see how long that 26 of simons lasts with the 6266. He is chucking a lot of boost at it thats for sure. Should make a build thread!!!

What Ideas do you have for the engine at this stage. Do you know what injectors, Manifold, Plenum etc you are looking towards?

mattis96 Proficient

mattis96

Posted
Posted

I have a front facing plenum with 90mm throttle body

Engine will be forged with cp pistons and spool rods, arp main, rod, head studs. Keeping vct inlet cam as dan made a good point about it. Head is built with new upgraded parts.

Fuel system will be 2 044 pumps from surge tank with nismo intank, 2000 Id injectors. Dash 8 fuel lines. I want the surge tank mounted under the car though for simplicity running flex fuel setup

6 boost t4 split pulse manifold, 4 inch turbo back exhaust

Will be pushing what ever turbo I get to maximum capacity with what the fuel can handle.

I will start a build thread soon.

How's your car going to Scott? ANy dramas?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      I definitely know the first rule here, look first, ask second. I've seen many people get roasted 😂 I found a few diagrams for the RB, but I'm yet to come across one for the VQ. From what I have read, the pump gets the +12v along with the FPCM, and it's the negative wire that gets passed through the resistor to regulate the voltage. So I assume I can just ground the negative wire at the pump to eliminate the FPCM control. But I really wanted to see the VQ circuit diagram first to make sure I understood it correctly. Once the new pump is in I'll do some testing to see how it behaves, and in the meantime, I'll keep looking for a wiring diagram. Thanks for your help mate, your time is greatly appreciated.    
    • GTSBoy
      Jacks that fit under GTR lips that can reach the subframe?

      By GTSBoy · Posted

      Maybe? I have the Supercheap ToolPro low thingo. It has a somewhat smaller diameter lifting "bowl" than you would expect on a workshop grade trolley jack, and a split rubber pad to suit that diameter. It clears the "N1" style skirts I have. Probably wouldn't if the jack's bowl and a suitably larger rubber block were in use. Having said that though.....you only need the rubber block to exist on the inner side of the pinchweld, so could carve away any rubber that fouled the skirt, leaving some there for "insurance" </simples>
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I used to do that (sills with rubber jack block).. ... then I got side skirts, and there's no way for the jack to actually work there, the jack pad itself on the jack is too big. Is the answer to use a... smaller (?) jack? Hmmm.
×
×
  • Create New...