Jump to content
SAU Community

Recommended Posts

Hey, I'm looking to upgrade my injectors in my S2 R33 GTS-t in preparation for my ATR43G2 turbo upgrade.

At the moment, I'm still running stock injectors and want to know what injectors are best suited to my power goals?

I've looked at Nismo items but are abit pricey and I'm leaning towards the Bosch, Siemens and stock S15 injectors.

My power goal is roughly 260-270rwkw, though I do wish to have a little but of headroom with the injectors (that is, I don't want injectors which will be at 100% cycle duty @ 270rwkw).

I'm leaning towards S15 injectors as I read they are drop in items and can be had fairly cheaply :)

Current mods:

- 3" dump/front pipe

- high flow cat

- blitz sus pod

- blitz turnflow intercooler

- turbosmart e-boost

- 3.5" kakimoto catback

- E-Manage Blue

- 12psi

Current power figure: 195rwkw

Any advice/recommendations would be appreciated.

Cheers.

Link to comment
https://www.sau.com.au/forums/topic/358069-upgrading-injectors/
Share on other sites

if your going to spend the money, i would just do it properly

nismo 550cs and be done with it

you may find stuffing around with s15s a pain

as there are differernt for ADM/JDM manual and auto as well and you have to find 6 as well

go for it if u want

but you may find it simply easier and over all cheaper in the end by going nismo's

bosch and siemens are fine as long as you dont have to mangle plugs, change rails etc

and you can hook them up. afterall, the nismo ones would be made by jecs or bosch anyway

No worries at all mate, thanks for the reply. I guess I'll forget about the S15 injectors then.

What sort of cc injectors will I need? I found a general rule of thumb was 1cc per hp so my power figure requires 400cc as a minimum. Is that correct?

What size are standard purple top RB25det injectors?

Cheers.

Alright then, that's good to hear. The only thing now is seeing if my Emanage will support 740cc injectors, which is why I need to know the stock injector size. It's around 370cc is that correct?

Also, series 2 RB25det use side feed injectors yeah? Are top feed injectors able to be used?

no. latency is the dead time, the time which an injector has power but isnt spraying any fuel. (the time it takes to open and then close again). different injectors have different latencys, so when changing injectors the tune needs to be adjusted not only for the bigger size but also the different latency, especially under light load around idle.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...