Jump to content
SAU Community

To R31Nismoid

Overnight Parts From Japan
 Share

Recommended Posts

Overnight Parts From Japan Apprentice

Overnight Parts From Japan

Posted
Posted

The entire reason I started the post was because I'm not interested in building a RB24. I have searched for builds, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a 2.4 Litre. The reason I started this build is that I wanted to know some information about whether the parts i mentioned would fit.

However I have found that skylines australia, is essentially a useless site, as it contains pretentious f**kwits like yourself, who believe they are gods, when they are merely little dicked faggots, with their keyboard warrior beliefs. As I'm a mech eng, i'm more than capable of working out the efficiency of an engine that is less than 3 litres and can thus make the conclusion that 3 litres will always ultimatly make more power than a lesser volume engine. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearforce1 top bloke.

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/
Share on other sites
Mr Sniper911 Community Regular

Mr Sniper911

Posted
Posted

The entire reason I started the post was because I'm not interested in holding a BBW. I have searched for BBW's, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a BBW just holding. The reason I started this is that I wanted to know some information about whether the penis i have mentioned would fit.

However I have found that skylines australia, is essentially a website, as it contains BBW Lovers like BOZ, who believe they are BBW gods, when they are merely giant little people, with their keyboard warrior skills. As I'm a little dicked top bloke, i'm more than capable of working out the efficiency of an penis that is less than 3 inches and can thus make the conclusion that 3 inches will always ultimatly make me frustrated and i will end up alone. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using drugs again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearback faggotry.

Fixed!

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744048
Share on other sites
Overnight Parts From Japan Apprentice

Overnight Parts From Japan

Posted
  • Author
Posted

to op

suck multiple dicks homo

to r31nismoid.. <3 yewww :wub:

Hey Charizard

I could have a dick in each hand and one in my mouth and still not be as gay as you, <3 nismoid? f**kn top bloke...

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744086
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • Kapr
      "Cheap" bolt on turbo on RB25DET NEO

      By Kapr · Posted

      Ok guys thank you very much. GCG highflow it is then 🙂 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      forgot to mention that when it does this it does not kill the engine, but I have not kept the pedal down long enough to let it, as I see no reason to beat up on it as its got to be something simple, small and dumb causing this.  And as soon as I let off pedal, the engine returns to its normal super smooth operation and rpms re-stabilize quickly, once below 4k. 
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Dose Pipe Sutututu
      Why am I hitting a power wall with my stroked RB25?

      By Dose Pipe Sutututu · Posted

      Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
×
×
  • Create New...