Jump to content
SAU Community

To R31Nismoid

Overnight Parts From Japan
 Share

Recommended Posts

Overnight Parts From Japan Apprentice

Overnight Parts From Japan

Posted
Posted

The entire reason I started the post was because I'm not interested in building a RB24. I have searched for builds, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a 2.4 Litre. The reason I started this build is that I wanted to know some information about whether the parts i mentioned would fit.

However I have found that skylines australia, is essentially a useless site, as it contains pretentious f**kwits like yourself, who believe they are gods, when they are merely little dicked faggots, with their keyboard warrior beliefs. As I'm a mech eng, i'm more than capable of working out the efficiency of an engine that is less than 3 litres and can thus make the conclusion that 3 litres will always ultimatly make more power than a lesser volume engine. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearforce1 top bloke.

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/
Share on other sites
Mr Sniper911 Community Regular

Mr Sniper911

Posted
Posted

The entire reason I started the post was because I'm not interested in holding a BBW. I have searched for BBW's, and there are some out there, but if you bothered to read the post that I started, I clearly mentioned that I am not chasing a BBW just holding. The reason I started this is that I wanted to know some information about whether the penis i have mentioned would fit.

However I have found that skylines australia, is essentially a website, as it contains BBW Lovers like BOZ, who believe they are BBW gods, when they are merely giant little people, with their keyboard warrior skills. As I'm a little dicked top bloke, i'm more than capable of working out the efficiency of an penis that is less than 3 inches and can thus make the conclusion that 3 inches will always ultimatly make me frustrated and i will end up alone. This post was about what I had already, and what i can do with it.

Please block my IP address as I'm at an internet cafe, I won't be using drugs again ;). I look forward to our next encounter, with my new account, at my new ip address. Look forward to more Bearback faggotry.

Fixed!

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744048
Share on other sites
Overnight Parts From Japan Apprentice

Overnight Parts From Japan

Posted
  • Author
Posted

to op

suck multiple dicks homo

to r31nismoid.. <3 yewww :wub:

Hey Charizard

I could have a dick in each hand and one in my mouth and still not be as gay as you, <3 nismoid? f**kn top bloke...

Link to comment
https://www.sau.com.au/forums/topic/359709-to-r31nismoid/#findComment-5744086
Share on other sites
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Latest Posts

    • nxh
      R34 4 door side skirt identification

      By nxh · Posted

      Legend. I ended up finding the facebook account of the owner of the first car i sent but sadly he deactivated the account. I think you’re right in saying it’s some sort of well done custom job. Really appreciate your help anyways.
    • GTSBoy
      boost source Size Garrett gt28 gen2

      By GTSBoy · Posted

      Totally equivalent. Stock often goes from the comp cover because that's where the actuator is also installed and the factory needs 2" of hose to make the connection - and it comes as a pre-assembled unit. They totally have a boost reference from somewhere between the turbo and the throttle(s). Oh, jeez. Just do it in M12 then. We don't actually care that much. I would expect any such AN converter fitting to rely on an o-ring or some other seal onto a flat surface under the flange of the hex**, because bolt threads are no intended to provide a pressure seal. unlike..... pipe threads. **which also requires a suitably flat and smooth surface on the turbo's boss to provide the seal.
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I also used NP   That’s were it’s seems to be the best place to fit it? All schematic shows also that it’s should be referenced from the turbo housing. But idk, I do see high hp cars without any connection or anything to their turbos, so I really don’t know how they connect their things
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      I do have loctite 243 and 246 and a few more models. I could drill it now in place and make new threads for m12 and order an4 - m12 coupling and fit that to the turbo. Run a braided hose to the EBC which I could get a an4 to 1/8npt 
    • timmy94
      boost source Size Garrett gt28 gen2

      By timmy94 · Posted

      So M12 and sealant should be fine?    NPT ” because that’s what I had and what I could get atm. 
×
×
  • Create New...