Jump to content
SAU Community

Fully Built 1000Hp Rb26!

scr33m
 Share

Recommended Posts

scr33m Enthusiast

scr33m

Posted
Posted

Hey guys ive got up for sale my fully built 1000hp Rb26 from a GTR skyline. Heres the list of the parts worth 22k+......

CP Pistons

Howard Rods

Head with mild ports

282 spec cams with retainers

ARP head and main studs

Ati balancer

Custom Valves

Custom springs

Jun oil pump

Trust sump with extension

Block has been specially prepped & cleaned

Crank has been prepped & fully balanced

For any questions pm me or msg me on 0448868384..cheers

Selling for $14,000 o.n.o, which is alot less than it cost to build the motor. It has been only driven around 1500kms so still new.

Link to comment
https://www.sau.com.au/forums/topic/360303-fully-built-1000hp-rb26/
Share on other sites
  • 5 weeks later...
  • 2 weeks later...
  • 2 weeks later...
rb26zed Enthusiast

rb26zed

Posted
Posted

Sorry, I'm not interested in buying your engine, but I am curious as to how someone spends the time, effort and of course money to build a $22000, 1000hp engine, drives it 1500km then suddenly needs to sell it at a huge loss.

scr33m Enthusiast

scr33m

Posted
  • Author
Posted

Sorry, I'm not interested in buying your engine, but I am curious as to how someone spends the time, effort and of course money to build a $22000, 1000hp engine, drives it 1500km then suddenly needs to sell it at a huge loss.

the guy i bought it off of got it built for his street gtr and decided to take it out to put it into another gtr for drag racing but decided he wanted an rb26/30 instead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • djr81
      R32 update from 1990's spec.

      By djr81 · Posted

      So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • djr81
      RB26DETT Sketchy boost mod?

      By djr81 · Posted

      Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...