Jump to content
SAU Community

Recommended Posts

hey doglet i'm in bris and can only get them here in bris, sorry dude

hey siu where bouts u live in brisbane and meet up sumwhere and compare our cars cos i got similar mods to urs and just got a dyno run recently as well. and yeah we'll sort something out wen yuo need sumfin. cya round

any1 else needing parts, please be aware that i can get brand new genuine nissan parts (not second hand) and should the part u are after is coming from japan it is a 1.5-2 week wait and also requires a 20% deposit. if the part needs to come from another warehouse/nissan spare parts joint in australia then 2-3days with 20% deposit, if coming froma brisbane warehouse then within a couple hours(24hrsmax) and a 20%deposit. so please take this info into account when considering thanks

redline: it would depend on parts like 6 platinum plugs for 32 my friend was quoted 110-120 i got it for him for bout 60-70 dollars. usually the more expensive the part the higher the saving

fatgtsr: not confident or prepared to send it interstate due to possible problems like wrong part/damage etc.(u never know) and it will be a hassle sending it back to bris for refund/replacement esp. if coming from japan. sorry to disappoint

I got a nissan key blank for my GTR - just wondering if its possible to check nissan databases or whatever to find the lock code (ie X----) so I can get a locksmith to cut the key for me???

if not ill just have to take off the door trim & find the door lock & check that out. Thanks

  • 2 weeks later...
Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...