Jump to content
SAU Community

Recommended Posts

Hi all ,

decided to strip my car down.

all parts are still on the car , car is complete for now.

if people are interested in the bigger bits such as motor/box then ill have it stripped down quicker.

someone come chuck a deposit on the motor and box :)

cusco tension rod $80

d1 garage castor arms $80

project mu slotted rotors (front) $100

d1 garage rear camber arms $100

kts rear cradle bushes $30

racing gear n1 circuit coilovers $1,000

nismo strut brace with cusco brake stopper $160

skyline rear strut brace $100

surge tank with lines and fittings $250

bosch 044 external pump $140

cusco half cage minus crossbar $300

sparco sprint fixed back $250

nardi deep corn copy $120

boss kit $45

hks evc5 ebc $300

gtr wing $150

rb25det motor minus turbo setup $1700 (needs new oil)

trust td05 with custom intake / greddy dump pipe / custom front pipe $1100

z32 afm $140

nistune rb20 ecu $400 (Tuned for engine setup with td05)

gearbox $900 (has slight whine)

18x8 /9.5 +45 $700

30mm bolt on spacers $100

27mm bolt on spacers $100

custom 2.5" blast pipes $250

Greddy boost gauge $60 (no light)

hicas lock bar $40

front mount intercooler with piping $250

signal straight through exhaust $600

r33 complete shell , with rego & plates $POA

cusco 2-way Mechanical Diff in housing $ 700

All parts sold as is

No warranty

Come inspect before buying

Postage at buyers expense

No COD

Will hold items if 20% deposit is paid on bigger items

If there is anything ive missed i will update the thread as it comes to my attention

contact: 0419 848 600

Edited by DamageInc
Link to comment
https://www.sau.com.au/forums/topic/362420-wrecking-r33-drift-car/
Share on other sites

Hi, I'm after the following parts:

1. Do you have any front bar indicators? If so, what do they look like and how much?

2. I'm after the front inner guard lining thing that covers up the section from the front inner guard to the front bar. If how much?

3. Am after both your set of 27/30mm spacers, I'll give you $150 both. Is this ok?

How much to post to 3012 POST CODE in VIC?

Hi, I'm after the following parts:

1. Do you have any front bar indicators? If so, what do they look like and how much?

2. I'm after the front inner guard lining thing that covers up the section from the front inner guard to the front bar. If how much?

3. Am after both your set of 27/30mm spacers, I'll give you $150 both. Is this ok?

How much to post to 3012 POST CODE in VIC?

1. keeping them with the front bar, which is staying with the shell

2. lost them years ago, ha

3. already got a buyer for the 30mm's mate

cusco tension rod $80

d1 garage castor arms $80

castor arms and tensionrods are the same thing though?

can you up load a pic of both sets so i can choose lol

Edited by tm_r33

you sure yournot thinking of sway bar.

do a google image search on 'r33 tension rod' and on 'r33 castor arm'

they the same thing bro

http://www.google.com.au/search?q=r33+cusco+tension+rod&um=1&ie=UTF-8&tbm=isch&source=og&sa=N&hl=en&tab=wi&biw=1920&bih=1077

cusco tension rod $80 SOLD

d1 garage castor arms $80 SOLD

project mu slotted rotors (front) $100 SOLD PENDING PICK UP

d1 garage rear camber arms $100 SOLD PENDING PICK UP

racing gear n1 circuit coilovers $1,000 SOLD PENDING PICK UP

skyline rear strut brace $100 SOLD PENDING PICK UP

surge tank with lines and fittings $250 SOLD PENDING PICK UP

bosch 044 external pump $140 SOLD PENDING PICK UP

gtr wing $150 SOLD PENDING PICK UP

z32 afm $140 SOLD

hicas lock bar $40 SOLD PENDING PICK UP

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...