Jump to content
SAU Community

Recommended Posts

Hi All,

Up for sale is my R32 Skyline GTST.

It has 107,000 kms

100k major service has recently been done, replaced water pump and all belts etc etc.

as well as at 105k service

Engine is running perfect

It will come mostly stock with RWC and Rego until March 2012.

Will come with a full exhaust and FMIC.

Very clean car with good paint and no tears on any of the seats.

Right now is has the following mods, which i can keep on for an extra price.

All parts are currently working in the car.

PERFORMANCE

-Cusco Zero Coilovers

- Ms Strut Brace

- Electronic Boost Controller (HKS EVC)

- GTR Sway Bars

- K&N Pod Filter

- HKS Turbo Timer

SOUND SYSTEM

- Alpine Type X Sub (with custom box built especially for R32 boot) – 1000 watts RMS<br style=""> <br style="">

- Alpine MonoBlock – 1000 Watts RMS

- Rockford Fosgate Punch Amp

- MB Quart Premium 6.5" and tweeters

- Zero Gauge Cables and stinger RCA

- 1 farrod Cap

- MB Quart Discus 6X9

OTHER STUFF

-Boost Gauge<br style=""> <br style="">

-Yellow Top Battery

- Front Rims – Volk GTC 18 X 9 +22 (in chrome which is rare) – 70% Maxxis tyres<br style=""> <br style="">

- Rear – Work VSKF 18 X 10 +33 – 90% Federal tyres

- viper alarm with 2 way pager.

BAD POINTS

The centre console is missing an ash tray and has a few cracks (all cosmetic)

Easily replaced and fixed, may even be able to do for you.

Any questions please call or text

0402 759 408

post-72035-0-21914900-1304250472_thumb.jpg

post-72035-0-11513100-1304250517_thumb.jpg

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When sanding across a convex panel, you need to sand, as much as possible, at right angles to the curve. If the panel is compound convex curved (ie curved in both directions) then you are SOL and have to use "craftsmanship" to get it right.
    • Today in Skyline arts and crafts!! I’ve made some progress.    had to put extra notes in there so I don’t stuff it up 😂
    • This sounds like me. And then why I leave shit that I had previously hobbled together broken. Lately I've changed strategies to "If I don't want to justify the money on decent stuff, I'm not going to justify hobbling it together". I'm still for DIY, but DIY it properly is more my thing. However, I am terrible on not setting up backups still... Which reminds me, I need to go backup some of my work VM machines... Oh, it's also why I've become a lover of building things into Docker Containers... Then I just need a machine that can run docker, and bam, that specific system is up and running, on the specific versions of everything I need for it to run (In the event a change in required software version breaks something else). Also, these days, my steep learning curves are spent with work related stuff, and on very varied projects, that my want to do other random projects like build a dashboard for my own car has dwindled away to "I just want the car running", which is my current PITA, as I'm getting the Landcruiser usable again, and it has just been non-stop the past 6 to 8 weeks of buying parts, and working on it. Oh, and tools that are meant to be fit for purpose... And they break, because 25 year old 4WD decides it's stronger... But by the time I have it ready to roll back out the drive way, nearly all the stuff in it will have been touched and serviced, so the damn thing better give me NO FREAKING ISSUES, for at least the next 50,000KMs! Just redone whole front of the motor, and resealed the up top stuff, replaced a bunch of things getting perished, new timing belt done, water pump, lower timing cover (Toyota diesel engine runs timing GEARS for the bottom half the motor, and a timing belt from halfway up to the top), new harmonic balancer, fix up the alternator, new thermostat, full swivel hub rebuild, new bearings and seals front and back, steering box rebuild, new battery, and today, it turns out a rear shock has let go, so four new shocks are about to go on order, and that will leave me with after the next run of work, to see if I need to order just a brake caliper re-seal, or if I'll need new pistons in them too. Oh, and I'll finish welding in the new floor sheet metal shortly too. Presently I just want it finished already... But once all the above is done, I still need to fully service diffs, gearbox, transfer, and motor. Then flush and bleed the clutch, and flush and bleed the brakes. But enough about our waffle, back to Duncan's heat problems... I think for Duncan he just gets a thermoswitch, and a manual switch to run some water misters. Thermo so it's only on above certain temps, and the manual switch so it can be turned off even if it is above certain temperatures. IE, switch on for "I'm now on track", then it doesn't need any "smart" computers that might try and do things wrong. And switch the thing off completely on the cool down lap, so when he stops in pits, there's not even a possibility of it dripping any water out to get him in trouble.
    • So I ran into the same problem. I got stuck in the cycle of again of putting putty sanding it, putting putty sanding it, because of a low spot. And notice my block is not completely flat with the panel, even though it's a long block. My panel is slightly curved. Is this an issue? Do I need something that matches the door perfectly, or no?    I do have the smaller flexible block that covers the width of the repair just not the length, I was experimenting with it again to but seems to be the same issue
×
×
  • Create New...