Jump to content
SAU Community

Recommended Posts

Hey guys ive just purchased a brand new dump pipe by Turbo Xs for my R33 Series 2 GTS-T i have put a picture below of the dump pipe, should i be paying someone to install it or is it fairly easy to put on without any dramas?? if any1 knows what is involved in putting one on lemme kno, also i have got a jasma catback exhaust so will this dump pipe be alrite even though i have a standard cat??

Cheers

3150nsi.jpg

Edited by SLY333
Link to comment
https://www.sau.com.au/forums/topic/363502-how-to-install-a-new-dump-pipe/
Share on other sites

That sensor looks like it is in a bastard of a spot!

Be very careful with the bolts in the back of the turbo, you don't want to snap them. As said spray them with bolt off or wd40 etc and leave that sit for a while. If the bolt feels like it's getting tight as your undoing it, it might pay to do it back up a few turns then start undoing it again so you don't snap it.

undo the sensor at the plug then unscrew it from the dump once you have it off the car if you cant get to it with a spanner while the dumps still on the car.

will give more power yes! and a different noise

those sensors can be a pain to get off, make sure you get the right size spanner onto it as they can be rather tight and the last thing you want to do is to have a spanner slip and stuff the bolt. Also get all new gaskets and personally i used a bit of gasket cement on them to make sure you get a decent seal

Dude, its definately job you can do yourself. I bought my first skyline (95 gtst) a few months ago and i have done everything with the exhaust myself. All my bolts including oxygen sensor werent too bad, some were pretty stiff but you get that. The guys in the post have given you good advice with the wd40, so follow that. Im not the most experienced with cars, and usually stick to just doing oil changes etc. Im lucky that i can always get my old man to help me with my cars, which comes in handy. I would definitely have a go yourself, and if your concerned just try get someone who is handy with the spanners to come round for a few beers!

I have found the skyline to be really easy to work with, and if you get stuck this site is an excellent source to get your answers.

All pretty easy, should be able to punch it out in about 2 hours working on your back with stands, obviously put the o2 sensor in the new pipe out of the car would be borderline impossible in the car. You can get onto 5 out of 6 bolts with a small 3/8th breaker and a 13mm socket (bottom 2 from under the car) I cut down a small 13mm spanner to get to the middle passenger side bolt.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
×
×
  • Create New...