Jump to content
SAU Community

Recommended Posts

Hi All,

I'm after a stuffed RB26 head. I don't care if it's cracked, warped, got a ferret stuck in a port (common problem on RB26's). Only condition is it must be very cheap. I just want it to put on a buggered block I have in the shed and make a dummy engine I can fit in the engine bay and see how everything is going to fit. Basically after something that was destined for scrap metal.

I'm also chasing a slave cylinder, throwout fork and bearing for an R34 GTT box.

Cheers,

Shane

Hi All,

I'm after a stuffed RB26 head. I don't care if it's cracked, warped, got a ferret stuck in a port (common problem on RB26's). Only condition is it must be very cheap. I just want it to put on a buggered block I have in the shed and make a dummy engine I can fit in the engine bay and see how everything is going to fit. Basically after something that was destined for scrap metal.

I'm also chasing a slave cylinder, throwout fork and bearing for an R34 GTT box.

Cheers,

Shane

i have a 20 head you can have if that any use to you.

i have a 20 head you can have if that any use to you.

Thanks, does anyone know if some of the studs on the inlet side line up between a 20 & 26? I know most of the exhaust studs do. If I can get a few to line up then it will do the job for what I'm after.

I'm also after the rear part of an R33 or R34 tailshaft if anyone has one.

i have a 20 head you can have if that any use to you.

Thanks, does anyone know if some of the studs on the inlet side line up between a 20 and 26? I know most of the exhaust studs do. If I can get a few to line up then it will do the job for what I'm after.

I'm also after the rear part of an R33 or R34 tailshaft if anyone has one.

all bar 4 of the studs line up between rb20 and 26 on the inlet and i think similar on the exhaust

i also have rear half of r33 tail shaft

and i have a rb25det head that is only any good as a paper weight so you can get the whole lot off me if you want.

Thanks, does anyone know if some of the studs on the inlet side line up between a 20 and 26? I know most of the exhaust studs do. If I can get a few to line up then it will do the job for what I'm after.

I'm also after the rear part of an R33 or R34 tailshaft if anyone has one.

if you need the yoke for the gearbox i have a new one spare

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I would just put EBC back on the "I would not use their stuff" pile and move on.
    • Can I suggest you try EBC directly again and link them to as many competitor catalogues as you can to show their listing is incorrect, eg https://dba.com.au/product/front-4000-series-hd-brake-rotor-dba42304/ If you have access to an R33 GTST VIN and your VIN, you could also use a Nissan Parts lookup like Amayama to show them the part number is different between 33 GTST and 34 GTT which may get their attention
    • So i got reply from EBC and they just this site where you can clearly see those 296mm fronts on R34 GTT. I send them photos and "quotes" that 296mm are not for 34 GTT and they are too small. But it will be very hard to return them cuz nobody here knows 100% and they just copy those EBC catalogue :-D https://ebcbrakesdirect.com/automotive/nissan/skyline-r34
    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
×
×
  • Create New...