Jump to content
SAU Community

Recommended Posts

Hey guys noticed this after a drive. If i came to a stop and was idling for a few mins the car would gently die. I was able to restart it straight away no worries.

Now it wont rev past 2000rpm, when you add more throttle it just pops as if it only had 2 running cylinders.

Eventually it will stall after idling for 5-10min.

Its a built engine with cams, gt35r, Pfc and all accompanying mods.

As of now it is undriveable and is just sitting in the garage

Ideas?

I am led to believe that this is a C.A.S issue?

Edited by r33cruiser

Afm has been checked by my mechanic, voltage and wiring is fine.

Will definitely go over my cooler piping again. I am only running 12psi-still on run in tune so I dont think a join has popped off. I will investigate my plumbing further tomorrow.

This happened to me for no reason all I did was put on my coil pack cover and started the car and idling like on 2 cylinders and would pop when you rev it couldnt figure it what it was and then after 30min started it again and drove up and down and it was back to normal still puzzled with what it could have been.

  • 2 weeks later...

Thought I would give you guys an update. Finally got some time to go over it today.

Due to my r34 cams I have had to use an r34 cas. I took off the plastic cover of the cas exposing the bronze disc inside. The car started and revved freely.

It appears that it was full of dust and that was restricting it.....well maybe.

Its revving fine now, it idles etc so lets hope it stays that way :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...