Jump to content
SAU Community

Recommended Posts

Hi,

I bought a R32 GTR about 5 months ago, it not a daily driver, but when I do drive it the suspension drives me insane. Im pretty sure that the coilovers I have are flogged out, the front end tends to bounce though bumpy corners (not fun!!!). I have the alignment specs from the previous owner and I cant see anything that could cause issues. The other thing that annoys me is that I think the suspension is way too stiff. Im not sure whether I should look at rebuilding them and getting new softer springs or just replace them. I cant seem to find any information on the net about the coilovers in my car, but I suspect that they are very old. The part number suggests that they are for a non-GTR, is this an issue?

Any advise/opinions on what I should do would be great.

Specs stamped on rear passenger side coilover:

DDN19-12511

HCR32-R 93E

TEIN

There is also a sticker but thanks to google, Im pretty sure it is just a Japanese tuning shop

"Signal Auto Senri"

If you dont think I should rebuild them, any suggestions on what to replace them with would be great. The lowest off the self spring rates I can find on new coilovers are 8/6kg (F/R). I think the standard GTR spring rates were around 4/3(??) I "think" I would like something stiffer than standard, but still comfortable enough to drive on our crappy roads for a few hours without needing a neck brace. Street driven only, no drag or track work (for now).

I can put up a pic if it helps.

Cheers,

Brendan

Link to comment
https://www.sau.com.au/forums/topic/365068-coilover-identification-and-advice/
Share on other sites

Nothing wrong with Tein but I don't know those numbers signify.

Have a look around this website but more usefully find your local Tein dealer/service agent and make some enquiries there.

http://www.tein.co.jp/products_search/jp/shashu_tekigo.cgi?lang=e&make=NISSAN

I think im going to look at replacing them with something else. Its probly going to cost around the same to get them rebuilt with new springs as it will to get a new set of BC Racing coilovers and then I get damper adjustablity too. I know the BC's arnt the best quality, but for the driving and km's I do, I think they will be fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Just had this happen to me too.  R32 GTR.   Also broke "just before going out onto the track" - someone up there is looking out for us... Very scary since I was about to do a narrow street course with zero run-off and curbs everywhere. Many people on here upgrading to billet uprights and R35 bearings?   Or buying new OEM knuckles?  I am not keen to replace with another s/h 30 year old fatigued part.
    • Top off with distilled water and see what happens. If you keep losing coolant then you know to start looking.
    • Nope.    Grab a varex and turn it down as you get close to home, win win? 
    • So, I've had my V36 for about a month now and have already copped an "excessive exhaust noise" notification from QLD TMR, reported by someone in my local area. It's a twin as per the original, and can have a bit of a throaty note to it when idling cold 😄 and if I do get up it a bit, it can be noisy, but it did pass a roadworthy inspection before sale, so.... ... but in the interest of being a good neighbour, I do want to quieten it down a bit. Is anyone here running a quiet aftermarket cat-back on their V36 or 370Z? And the big, bold question: does an aftermarket cat-back really make much of a performance difference on these cars?
    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
×
×
  • Create New...