Jump to content
SAU Community

Recommended Posts

Hey guys,

All this stuff is in great conition, It was taken out of my car when i did my conversion its just been sitting around.

Stock R34 Turbo - $250

Stock R34 370cc Injectors - $350

Stock R34 Air filter Box with K&N Panel - $100 (going cheap as thereis a hole in the bottom of the box where a pipe was going through from thefrontbar for better airflow)

Stock R34 Front Bar $80 (will need paiting)

Stock R34 Bonnett Hinges - $70

Stock R34 Bonnett Lock - $80

Stock R34 Fuel Pump - $30

Stock R34 4500k Xenon globes - $30

Stock R34 front orange indicators - $15

Stock R34 Piping between turbo and airfilter - $10

Aftermakrket R34 Camberarms - $100 (Brand NEW)

Aftermarket R34 GTR Seat covers -$40

02 WRX Bugeye front/back seats -$400

PICS BELOW

If anyone is interested please PM me or sms me on 0400 899 981

post-51275-0-11242100-1306268807_thumb.jpg

post-51275-0-02878000-1306269751_thumb.jpg

post-51275-0-90833400-1306269763_thumb.jpg

post-51275-0-24549100-1306269773_thumb.jpg

post-51275-0-96179000-1306269782_thumb.jpg

post-51275-0-95546000-1306269790_thumb.jpg

post-51275-0-42152200-1306269799_thumb.jpg

post-51275-0-90228900-1306269807_thumb.jpg

post-51275-0-52291200-1306269818_thumb.jpg

post-51275-0-71395600-1306269825_thumb.jpg

post-51275-0-76310400-1306269840_thumb.jpg

post-51275-0-45582300-1306269850_thumb.jpg

post-51275-0-56039300-1306269861_thumb.jpg

post-51275-0-78790200-1306269871_thumb.jpg

post-51275-0-99638900-1306269880_thumb.jpg

post-51275-0-60534600-1306269893_thumb.jpg

post-51275-0-28776800-1306270219_thumb.jpg

Edited by BL35ED

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
    • Yes then it will turn on but I want the car features to work  
    • My thought is if you were just moving it forward and the upstream geometry remained the same, then no difference at all. But because the current one has the filter direct into the AFM inlet, you effectively have the best chance of a completely symmetric air flow profile upstream, and in, the AFM, whilst the aftermarket inlet thingo has a (small, to be sure) bend between the filter and the AFM. That would bias the flow to the outside of the bend (downstream of the bend) which might well reduce the size of the signal seen by the AFM, for the same total flow rate. Having said that: If you're proposing to make your inlet look like a hybrid of your existing one and the aftermarket one, such that there is no bend where the filter is clamped on... then I say it will be just fine. If there is going to be such a bend, then, if you can align the insertion of the AFM blade such that it is at right angles to the plane of the bend, then there is a better than even chance that the centreline velocity where the blade is will remain more or less the same, and the velocity will just be a little faster to the outside of that, and just a little slower to the inside. **This is not professional investment advice and you should consult a suitably qualified ouija board, tea leaves or the intestines of a goat for more accurate prognostication.
    • Hi Tao, Thanks for your reply.  It's been a while and I managed to get the valve stem seals replaced with the head on the car.  Unfortunately this didn't solve my issue, the car still smokes a lot after idling (to be honest during idle you can see a bit of blue smoke from the exhaust), same after deceleration. I will try disconnecting the valve cover breathers, do I leave the PCV valve in? By engine oil drain pipe, do you mean the turbo oil drain?
    • What about if you just give it direct 12v and earth?
×
×
  • Create New...