Jump to content
SAU Community

Recommended Posts

Hey guys,

I hope this is the right place to post this.

I accidently gutter rashed a bit of the outer lip on my rims this afternoon. Shattered as I've owned these for nearly 2 years and have not had a single scratch mark on them and have always taken exceptionally good care of these. Rims in question are 18" Work XD9's in the MBG colour (Madbray/Magnesium-Gunmetal with polished/machined lip).

I was trying to get into a really tight reverse parallel parking spot and went in a little too deep then felt the rims scrape the gutter softly. I was hoping that there wasn't much damage done as I hit it very gently. After I assessed the rims there was only a slight scruff mark on the front left rim (not deep, around 4-5cms in length) and the rear left rim has 2x 1-3cm scruff marks. Both along the edge of the outer lip and barely noticeable when viewed from more than 1-2 metres away.

However, I am extremely fussy about things that I own and love so I went and tracked down a wheel repair specialist. After a quick search I found 2 that was based in Melbourne but was only able to get through to one. He comes out to you and all he needs is access to your car and a power outlet to perform a spot repair of gutter damaged rims. The price he quoted me though was $165 per rim. I thought it was a bit on the expensive side. I was hoping for more like $150 for both rims.

He seemed genuine and also asked me what brand and type of rim it was so I replied they were Work Japan rims with a machined alloy lip. Apparently he has worked with Work rims before and according to him the spot repair comes out quite good and blends in well with the original lip so it won't be that obvious (was told that some machined lipped rims don't tend to blend in very well once repaired and the spot where the repair was undertaken is often quite noticeable).

What do you all think? Should I even bother to have it repaired? Like I said, I'm very careful and always cautious whenever I drive and park but obviously it might happen again and then I'll have to spend money fixing again it a second time. My cousin told me that he wouldn't bother as the damage is not very bad and would only spend the money to fix it if he was going to sell them or something. I don't plan on selling them anytime soon as Work does not manufacture this particular colour/finish anymore so I want to hold on to them for as long as I can.

I'll post up some photos so people can see what I'm talking about.

Alternatively, I googled some other ways to repair the small marks and a lot of people have put up DIY's and they all seem fairly straightforward. I came across one guy who repaired the damaged machined lip on his Work VS-XX's and posted before/after photos. The end result looked amazing. He used a combination of low and high grit wet/dry sandpaper plus metal polish to finish it off. Apparently took around 90 minutes per rim. I'm not completely comfortable with going down this route though because I'm worried that I might do more harm than good as I'm inexperienced with sanding and grinding etc.

post-62214-0-97359500-1306831626_thumb.jpgpost-62214-0-81273300-1306831639_thumb.jpg

post-62214-0-90820000-1306831899_thumb.jpgpost-62214-0-00212500-1306831905_thumb.jpg

Edited by GT32
Link to comment
https://www.sau.com.au/forums/topic/366245-gutter-rash-repair/
Share on other sites

I have a wheel repair guy up here that will weld in metal filling if needed & machine the lip for $50 a rim for perfect brand new looking results

but yeah he needs the rim off the car with the tyre off the rim...

get it fixed one way or another, you know everytime you look at your car it will stick out like dogs balls to you, even though no one else can perhaps see it...

Yeah I know. Sometimes I think I have OCD or something when it comes to my car. It's really bad, lol.

It was bound to happen sooner or later anyway. No rims will stay in perfect nick forever so I was kinda expecting it. At least I went for 2 years without putting a single mark on them, fair effort in my opinion. My cousins brand new TE37's on his S14a was dinted and slightly gutter rashed only 3-4 weeks after he fitted them. He was absolutely pissed.

You know what, if I was up in QLD I would take your suggestion and get it done through your guy in a heartbeat. Only problem is I don't really want to have to post the wheels up there (and also have to remove the tyres etc). I know it's cheap but it would seem like more trouble than what it's worth. The guy I spoke to will do it with the rim still on the car if the lip damage is only minor and cosmetic. It's now just a matter of whether I willing to pay him the $330 for both rims to repair some 2-4cm marks...

Thanks for your suggestion though, much appreciated.

Edited by GT32

I'll try getting through to some other repairers throughout the week. I tried calling too late today and most of them were already closed. I think this guy is expensive purely because he comes out to you where ever you are in Melbourne. Assuming I can find another company that will perform the same type of repair in-house if I drop off my car or rims directly to them then no doubt it would be much cheaper.

Edited by GT32

Just got off the phone from another company. He quoted me $150 per rim to repair. So basically only $30 cheaper than the previous quote but I have to drive the car there or drop the rim/s off to his workshop. At least it's getting a bit cheaper...

I can't seem to find very many places around Melbourne that does these sort of repairs.

Maybe I should not worry about it right now and just live with the gutter marks for the time being. Then if and when I curb another gutter I'll get it repaired when the damage is more severe so the price will seem more worthwhile.

some places offer to repair rims but dont actually do it themselves and they turn out to be a middle man and add their own profit on top of the actual repair...

be sure your talking to the workshop that actually does the work.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
×
×
  • Create New...