Jump to content
SAU Community

Recommended Posts

Basically fited a 3.5inch exhuast to my 33 with 270rwkw and its got a valve inside the exhuast, its the dodgy version of the varex

the exhuast is only sort of quiet when the valve is fully closed, but the gases hav no where to go.

Is it ok to drive around like this to get less attention or is the pressure to high? ( il be driving under 3000rpm)

Link to comment
https://www.sau.com.au/forums/topic/366876-varex-exhuast/
Share on other sites

Its a knock off

its a butterfly valve in the exhuast and when its closed its like putting your hand lightly over the exhuastvpipe to slow flow

its still got lots of flow i imagine becuase its stillso damn loud but lags like all hell when closed

Car still starts up fine when valve is closed fully

( i imagine even when the valve is closed fully its not the same size as inside diameter of pipe i.e. Its a 3inch valve mabye, or it dosent close completly)

cheers

Link to comment
https://www.sau.com.au/forums/topic/366876-varex-exhuast/#findComment-5851899
Share on other sites

Its a knock off

its a butterfly valve in the exhuast and when its closed its like putting your hand lightly over the exhuastvpipe to slow flow

its still got lots of flow i imagine becuase its stillso damn loud but lags like all hell when closed

Car still starts up fine when valve is closed fully

( i imagine even when the valve is closed fully its not the same size as inside diameter of pipe i.e. Its a 3inch valve mabye, or it dosent close completly)

cheers

Yes I know what a Varex is I have one, I'm saying where in the exhaust is the valve? In the end muffler like a Varex or half way along the exhaust like the Apexi wunder valve? Varex use recirculation through a smaller hole that leads into another muffler...it's a much better/safer design when closed off than the Apexi valve. Either way it should be fine, just avoid boosting and high RPM.

Link to comment
https://www.sau.com.au/forums/topic/366876-varex-exhuast/#findComment-5851981
Share on other sites

Nah im not but im in traffic very often and seem to have undercovers behind me often, just need it to sound relatively stock

iv got a catback stock systen with 3.5inch flange to bolt straight on for regency if need be but in that case id be screwed from supporting mods and suspension

Link to comment
https://www.sau.com.au/forums/topic/366876-varex-exhuast/#findComment-5852175
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
    • the top black section is bonded to the silver section with some form of rubber. I assume to isolated NVH from the box
×
×
  • Create New...