Jump to content
SAU Community

040

whitenight27
 Share

Recommended Posts

loymclure Proficient

loymclure

Posted
Posted

I remembered a thread from many moons ago and did a search for it, i think this is what you are after

http://www.skylinesaustralia.com/forums/topic/191347-040-into-stagea/page__p__3442797__hl__bosch+040__fromsearch__1#entry3442797

good luck.

Link to comment
https://www.sau.com.au/forums/topic/367759-040/#findComment-5865781
Share on other sites
loymclure Proficient

loymclure

Posted
Posted

Had one in mine

Easy as piss to install

Will just fit into the stock cradle,couple of stainless cable ties and she"ll be apples

Till it fries,or you get sick of the noise

what did you replace your's with after you got sick of the noise?

Link to comment
https://www.sau.com.au/forums/topic/367759-040/#findComment-5866777
Share on other sites
leetom Proficient

leetom

Posted
Posted

as stated fits std cradle(just) with a bit of modifacation, from memory you dont use top part of cradle due to larger diameter of 040, i found the hardest part sliding the cradle back on it's posistioning rails, and i hardly notice the pump noise only on priming and then nothing, and also mine came with a non return valve which i removed hence a little bit longer to crank over,no big deal.

Link to comment
https://www.sau.com.au/forums/topic/367759-040/#findComment-5867096
Share on other sites
AAA34T Community Regular

AAA34T

Posted
Posted (edited)

i put a walbro i have been told the 040 is similar in mine last week took 10min.

The only mistake people make is in the tank.

*On the line there is a plastic t peice which is a pressure bypass valve and it wont allow mutch more pressure

than the standard pump you MUST remove it to get max flow. i found out about it on the dyno and had to remove

it on the dyno.

*and the new pump uses more power so upgrade the power supply to the pump.

mine is just as quiet as the standard pump so far so good

Edited by datzla
Link to comment
https://www.sau.com.au/forums/topic/367759-040/#findComment-5867459
Share on other sites
Tangles Grand Master

Tangles

Posted
Posted

with the 040 you'll want a direct feed from the battery

also make sure to position it as LOW as possible so you dont have issues with the tank when 3/4 empty.

with my 040 installed 4yrs ago have never had any issues, can run the fuel tank almost dry as it is situated as low down as possible.

Link to comment
https://www.sau.com.au/forums/topic/367759-040/#findComment-5867704
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Latest Posts

    • GTSBoy
      Looking for someone with a R34 front bar

      By GTSBoy · Posted

      That looks good, but I think you're going to need much beefier side skirts now.
    • GTSBoy
      Most women will agree that parking is the most taxing part of driving

      By GTSBoy · Posted

      They are daft and there's a reason it never caught on. Steering feel? We don't need no stinking steering feel!
    • GTSBoy
      new 1.5 LSD issues/concerns

      By GTSBoy · Posted

      I gotta pull you up on this. It's driving me crazy. A shutter is something that closes, like over a window or in a cmera. The word you want is shudder. That LSD is clearly f**ked. Take it to a diff shop and get it disassembled and examined by an expert. YOu might have plates welded together or something equally crazy.
    • GTSBoy
      M35 Brake caliper replacement

      By GTSBoy · Posted

      Define "starting to fail". Wy not just rebuild them?
    • GTSBoy
      S1 rb25/s14 starting problem

      By GTSBoy · Posted

      Check the Nistune doco. There are a few assumptions being made here that might not be valid. I will list the things that occur to me: Base map. Base map for what? Base map for Z32? Then the cranking pulse width is probably wrong for an RB25. The extra 500cc of capacity might well be enough to prevent it from catching. Base map for RB25? I don't think you can load one of those into a Z32. You have to just make the settings correct for an RB25 in the Z32 base map. That is either K or the TIM to get the pulsewidth right. Loom. You bought a loom for an RB. And you plugged it into a Z32 ECU. Did you make sure that any iwre differences were swapped. From memory, there's at least a couple. And as per the others, I would suggest making sure that the fuel pressure is correct while cranking and that the injectors are actually flowing as expected. They really must come out and go on the bench, unless you do find that you have messed up as per above points. I would also suggest watching in Nistune to make sure that everything is reading correctly. That the correct binary flags are raised at the right time (like the crank signal), that there's no stupid values in K or TIM. That you have not got mismatched firmware for the ECU and/or a wrong image loaded.
×
×
  • Create New...