Jump to content
SAU Community

Recommended Posts

if you have a multi meter or even test lights, try and probe each of the possible wires (shouldnt be too hard to figure out the possiblities)

if you have enough of it and want to take it to a shop, try power international in mitchell

the wire for your starter motor is a big fat white with a black trace coming off your key barrel. (Or possibly black with a white trace) Its been a while so my memory is shit house.... just probe it with your test light and turn the key to start. You have to take the bottom part of the steering surround off to get to it. There are possibly other areas where you can get to the wire that will make it a shitload harder for a theif to get to, but this would be the easy way of doing it. You could use a relay and set it up, so that it takes a theif time to find it, and hide it in the engine bay somewhere. But then if he knows what he is doing he can start the car anyway. Slow down tactics are as good as it will get, Tow trucks can override any alarm.

I would immobilise the fuel pump, because if you start playing with the ECU and use your test light, there is a possibility you can blow it up.. You will need to probe for the wires though, cause I haven't touched them myself, so I don't know.

And the door sensor, is it an actual sensor?(I dont install alarms) Or does it just sense the power from the interior light switch? If its the latter I would try and get my hands on a wiring diagram, then you would be able to source power from a central point with the switches combine to turn on the light.

Sumo

P.S. im only a 1st year.... dont listen to me - No one else does :rofl: lol

Stirlo

I did this myself as well (saving a bucket load of cash) and I had to trace the wires for about an hour. I'm still trying to get the central locking to work, but seeing as it only has an actuator on the passanger door - I can't see it working in the short term until I purchase one for the drivers door....

Did you manage to get around this? PM me and I'll run through the wires I used.

DAN00H

DANOOH.. thanks I'll take you up on that, and hey did you end up getting your side intrusion bars installed? if so where?

its funny that only your passenger door has on, mine is the other way only my driver door has one, they donr cost much any way one about $30 from strathfield..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...