Jump to content
SAU Community

Recommended Posts

  • Replies 54
  • Created
  • Last Reply

Top Posters In This Topic

ladies, ladies....an hour and a half?......u gotta b kidding?

a friend of a friend of a friend did the trip from troppo (if u dont no, dont ask) to ryde, via fox valley rd/yanko road in 22 mins one night......an an ASTRA....u guys drive skylines...who needs an hour and a half? :D

have a great day @ tha show n shine guys

(Neither SAU nor myself actively condone speeding, or reckless acts on the road..keep it for the track.....drive safely)

ladies, ladies....an hour and a half?......u gotta b kidding?

a friend of a friend of a friend did the trip from troppo (if u dont no, dont ask) to ryde, via fox valley rd/yanko road in 22 mins one night......an an ASTRA....u guys drive skylines...who needs an hour and a half?  :D

have a great day @ tha show n shine guys

(Neither SAU nor myself actively condone speeding, or reckless acts on the road..keep it for the track.....drive safely)

i know this friend of a friend of a friend, true story... :wavey:

Is this cruise up for entrants or spectators or either? :D

You're welcome to cruise up with us if you want, but we're aiming to get there at 8:30 and setup... Spectators aren't really arriving until 10am, so it might be boring for you to get there so early...

If I had a choice I'd choose SLEEEEEEEEEEEEEEEP!!!!

actually merli thats a good point :D

might cruise up with some friends later on in the day :D hope to meet some of you guys up there ;)

No worries mate, make sure you come up and say hi to us... We don't bite :rofl:

Ash - you poof ! Come OK - Will be heaps of fun - Come support your club ! ! !  

 

BTW - Did I say tell you that I will be kickin you arse on the 8th ! :rofl::P :P

ok u convinced my, but if you try and make a move on me :kick:

if i have said it once i have said it 1000 times im not a poof, sorry... you'll just have to find it somewhere else ;)

:D

hehe I won't know who I'm saying hi to :P Any quick intro's? :P

Hmmmm... perhaps we need a members page with photos and bios :D Just like all those ricer "racing team" websites like...................... Team Evade :rofl:

This is me: http://photos.fortheboyz.com/0401niki/imag...es/DSC05215.jpg

And I'll be going around taking photographs all day, or sleeping in my car (Midnight Purple R33 GTR)...

Hmmmm... perhaps we need a members page with photos and bios :P Just like all those ricer "racing team" websites like...................... Team Evade :rofl:

This is me: http://photos.fortheboyz.com/0401niki/imag...es/DSC05215.jpg

And I'll be going around taking photographs all day, or sleeping in my car (Midnight Purple R33 GTR)...

hello all... that sounds like a good idea... are there any cruises happening soon that are at night? looking forward to meeting all you guys... but im a shy boy




  • Similar Content

  • Latest Posts

    • @Murray_Calavera  If I were an expert I wouldn't be in here looking for assistance.  I am extremely computer literate, have above average understanding on how things should be working and how they should tie together.  If I need to go to a professional tuner so be it, but I'd much rather learn and do things myself even if it means looking for some guidance along the way and blowing up a few engines. @GTSBoy  I was hoping it would be as simple as a large vacuum leak somewhere but I'm unable to find anything, all lines seem to be well capped or going where they need to be, and when removed there is vacuum felt on the tube.  It would be odd for the Haltech built in MAP to be faulty, the GTT tune I imported had it enabled from the start, I incorrectly assumed it was reading a signal from the stock MAP, but that doesn't exist.  After running a vacuum hose to the ECU the signal doesn't change more than 0.2 in either direction.   I'll probably upload a video of my settings tomorrow, as it stands I'm able to daily drive, but getting stuttering when giving it gas from idle, so pulling away from lights is a slow process of revving it up and feathering the clutch until its moving, then it will accelerate fine.  It sounds like I need to get to the bottom of the manifold pressure issue, but the ignition timing section is most intimidating to me and will probably let a pro do that part.  Tomorrow I'll try a different vacuum line to T off of, with any luck I selected one that was already bypassed during the DBW swap. @feartherb26  I do have +T in the works but wanted to wait until Spring to start with that swap since this is my good winter AWD vehicle.  When removing the butterfly, did it leave a bunch of holes in the manifold that you needed to plug?  I thought about removing it but assumed it would be a mess.   I notice no difference when capping the vacuum line to it or letting it do its thing.  This whole thing has convinced me to just get a forward facing manifold when the time comes though.
    • Update: tested my spark plugs that are supposed to be 5ohms with a 10% deviation and one gave me a 0 ohms reading and the rest were 3.9ohm<, so one bad and the others on their way out.
    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
×
×
  • Create New...