Jump to content
SAU Community

Recommended Posts

So I was exiting out of my mate’s apartment basement car park at Wolli Creek the other day, it has a really steep (30 degree?) and tightly curved sloped driveway which also happened to have a little pool of water at the bottom flat portion of the drive. Now my mate in his stock Lexus IS200 went up this drive as easy as a snake sliding up a fence. Following him, I got like 1-2 car lengths up the drive and couldn’t go further – so much excessive wheelspin and could smell the tyre burning (thought it was the clutch at first).. 3-4 attempts and no luck. I even pulled up the handbrake on the slope, gave it some revs, then dumped the clutch normally, while putting the handbrake down, and still wheelspin at 3,4,5,6k rpms…

Got my mate and another guy to sit in the backseat to get better traction and we only JUST managed to crawl up in centimetres, wheelspinning as before, after the second traction we went up the slope easily, just at the bottom curved bit which was also wet.. My R34GTT has quite firm rear Cusco adjustable coilovers and the front end is a noticeable bit lower than the rear – same Cuscos in front.

My other mate with his stock Nissan Tiida who lives on the block never had this issue before.. So you can imagine them both ribbing me about how my high performance turbo car couldn’t get up that ridiculous driveway when their shopping trolley rides slide up and down like pros.

Anyone got any suggestions as to whats wrong with me not getting traction – hard suspension, front bit lower than rear?? – my tyres are really good – 235/18s, my traction control dosen’t work though, the light in dash is always off.

Maybe I was revving too much, but still? The lexus is a manual and I do know how to drive haha so thats not the issue, I even thought my car is pulling too much torque at low revs causing the wheelspin, but then a lot of you guys are pulling waaay bigger numbers than me and I've never heard of anyone bring up an issue like this..

Your skyline has way more torque than those other cars.

For a steep hill/driveway ( AND WET!!! ) you would need to ride the clutch quite a bit or like you did handbrake start, but dont rev it so high, creep it.

More power = more wheelspin, keep the revs down low, 1-2k range.

Edited by jay-rod

Dunno mate, bought it like that, that was the only thing in my car that dosent work, thats why its pretty dangerous in the wet, even driving it normally, wheelspins very easily, it does have the 2nd traction control butterfly in the intake though, I think either the unit is fuct or the fuse is blown..Anyways I am pulling a kinda healthy 545Nm torque on the stock turbo, tuned to awesomeness by DVS Jez on SAU

My question is - what happened to your traction control system? Anytime I've been in that situation, traction control would kick in and make it fine.

As far as i know Traction control does not stop both tyres from spinning after they have started.

It only stop loss of traction from the beggning.

So if he floored it, traction control can only do so much.

But yes no TCS would not help either :P

Edited by jay-rod

I did strongly think its my stiff suspension, but my tuner said my suspension is beautiful compared to the really hard race-type suspension that he is used to... Could be that my low rpm torque is a bit much for that slippery steep slope..?? The IS200 also a rear wheel drive, didnt have any issue at all, and niether my other mates Tiida - which would have more traction as its a front-wheel drive with the heavy engine in front?

I always thought the R34 has a good front-rear weight distribution although not as good as a mid-engine mounted car, so thought how the hell is the weight distribution causing this issue or is it something else..

I did strongly think its my stiff suspension, but my tuner said my suspension is beautiful compared to the really hard race-type suspension that he is used to... Could be that my low rpm torque is a bit much for that slippery steep slope..?? The IS200 also a rear wheel drive, didnt have any issue at all, and niether my other mates Tiida - which would have more traction as its a front-wheel drive with the heavy engine in front?

i just think you gave it to much throttle.

Have you checked all your fuses? The traction control not working could simply be the previous owner taking the fuse out or it could have blown?

*Edit - If problem persists buy a GTR :happy:

Edited by r32line

Anyone else had this problem? Nobody thinks its my stiff suspension and heavy engine in the front = less grip? I must say its very easy to wheelspin in this car, even in the dry straight roads, when coming on boost suddenly..

Doesn't the traction control system in R34s cut power by closing the throttle body? If this is the case might be able to get up the driveway if you use more delicate throttle control... or no throttle at all

To be honest, I'm thinking either diff or tyres (or a combination of the two). You definitely won't be going anywhere if you are single spinning... I remember trying to drive my cousin's Commodore onto my lawn and I got stuck because all it could do was peg leg!

Stiff springs on the rear end is probably a contributing factor but not the cause

Yeah sounds like you're just giving it too much. Only time I ever had similar in my old 33 was when I had bald tyres, with good tyres you should be able to just take it easy and slip the clutch a little.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • (it is a brand new ported mellings pump) I suspect the lack of pressure is due to the leak. It was *not* that low in other logs of oil pressure in the past. It wasn't that hot either, but not far off.
    • Would a Mellings oil pump be a viable option  From my time with a LS, and talking to tuners and LS specialists, the "weak" OEM oil pump is one of the first things they recommend to swap out if I was going to give the engine any high RPM I opted for a Mellings high volume, with the high pressure springs and I never had a issue with it Cost wise they are not expensive in the scheme of things 
    • Just bought a 2002 Stagea 250tRS VR-X Four AERO VQ25DET and spent the last two weekends cleaning and detailing it.. still have to do the wheels and the engine bay but the rest of it came up nice. Imported 2011 to S.A. and I'm the third owner since it was imported. I met the guy who brought it over, he went to Japan and picked out the car, bought it and ordered the wheels. He also gave me a list of stuff he did to the car with receipts. Coil overs (I have the original springs), 3" exhaust from the dump pipe back no cat, Custom dump pipe,(I have the original exhaust), Plenum spacer, 18" custom Work XSA wheels (need restoring, I've made a start..), Shift kit put through the 5 speed tiptronic auto, TV and menus/screens changed to english, Australian DTV tuner installed in rear. I've just had four new discs and new pads as well as all the fluids including the brake fluid replaced. I have all the receipts for the last 15 years and the import papers in a nice folder. Car looks great, goes like hell but fuel economy is not a thing lol.. pics next..
    • I ended up in this rut again lol, and used a shit ton of filler. One thing I can't understand is, even after using a big long block and going in long X pattern strokes, I always end up at bare metal again with no filler, and my repair started at one end of the door and now I've chased my tail to almost the other end of the door. I was thinking of hitting the panel with a hammer where it might be a high spot and making everything low then filling it, I did this on a small section on my other door by mistake and I think I fixed it lol. Is this a bad idea? The other thing is with guidecoat, whether it's the powder or spray, after I sand all the guide coat off, it doesn't reveal anything for me in terms of high spots and low spots and makes it especially hard when it's bare metal (at least in powdered form), am I doing something wrong here, or likely a high spot I keep going over and creating valleys? Lastly, stupid question but, is it possible that after sanding if I only sand over the filler area where I know to be a dent that it's impossible for me to dig into that dent? Unless there are other problems which I missed.  
×
×
  • Create New...