Jump to content
SAU Community

Recommended Posts

Don't thnk the traction control would help if anything it would make it worse.

In my R34 when the TCS kicks in it cuts power for a good second or so. So if it happened whilst he was on a steep driveay he wild just be sliding down slowly down the driveway :)

I only gave it some AFTER goin up a car length from flat area, then it started wheelspinning and not goin up, so i freak out n apply more gas hehe- and effectively doin a burnout!

Driving style in my opinion.

You didn't think to try get a slow roll happening before you hit the driveway?

& also did you try letting the clutch out with no throttle, getting a tiny little roll-on, or at least loading the driveline, then gently accelerating?

545nm, a wet 30 degree slope and no traction control. Yep, that'd do it.

+1

Did you try getting a little headstart? Reversing back then going at it hard?

"Get a bigger hammer" comes to mind..

Maybe you got a point, WLSPN, you could be right, I didn,t do those things, to the guy below you, VONCINA, ha ha yeah I tried that of course, all I got was massive wheelspin and burning rubber lol...

sounds like driving style is playing a bit of a part in it, and the stiff suspension may be playing a part if it isn't a smooth transition from flat to steep, mainly if you have to take it at an angle as the inside wheel probably has bugger all weight on it. a mate of mine had a ceffy where if you jacked up a front wheel the rear wheel on the same side would come off the ground it was so stiff.

was it spinning both wheels, or just one? if both then it is a diff issue as it isn't engaging the LSD. not saying that the diff is shagged, but it is worn.

to be honest, the tida should've had the most problems going up being fwd. all the weight would be over the rear wheels and the front wheels would be light. there is one intersection in town on a steep hill and if you try to take of with any sort of haste in a fwd it will spin the wheels. in a rwd car you can take off fast easily.

my advice would be to simply idle up it with bugger all throttle. keeping it off boost will drastically reduce the chance of wheelspin and it will be putting out much less torque than the lexus would be. if it still whelspins then it is your suspension and your diff.

If you were trying to go up slowly, then its not rpm or torque, because you regulate that with the clutch. Still suspension will definitely be a problem, as it will significantly un-weight one wheel, in which case you really need a working LSD to get any forward movement.

Any idea if both wheels were spinning or just one?

Don't know about that, my mate who was outside watching pointed out that the left rear wheel (outside of the curved driveway) was spinning but that was because he couldnt see the right inner wheel from his standpoint. I dont think its the diff/LSD because my car had straightened itself up on the straight part of the terrible slope and then wheelspinning like crazy. Which means both rear wheels getting equal grip at that time..

By the way my turbo kicks in around 2500rpm when it sees positive boost psi, by 2800-3000rpms it is at 12psi. Around 2500-3000rpms is what I would have been doing going up the slope after it started losing traction completely.... I would have driven in at 2-2500, it slipped, and then gone to 3000rpms and up to keep it from rolling back - but it never rolled back,. With the handbrake on and the car angled up the slope, I let the clutch out normally and throttle would have been 2500 and up - and massive wheelspin without movement.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...