Jump to content
SAU Community

Recommended Posts

come buy/try my meisters if you get desperate, similar sized fronts. another inch wider at the rear

depending on what your trying to acheive, a lower offset and more width would look better. i dont think CR kais would suit though

an 8.5 +30 and 9.5 +30 sits pretty well with very little camber, but if you want width, stretch and camber add an inch all round and drop the offset

Sedan offsets are way weaker than the coupe fyi. On my coupe I run 18 x 9.5" +20 on the front and 18 x 10" +12 on the rear and both sit nicely flush - mind you that is with some camber as well.

You should post this question in the V35 section to get better answers in future :

http://www.skylinesaustralia.com/forums/forum/170-v-series-skylines/

FYI there are only a handful of V35 owners on the SA forums.

Stock 17" sedan wheels are an awful 17 x 7" +45.

Use the following link to assess tyre offsets :

http://www.1010tires.com/WheelOffsetCalculator.asp

The answer to your question is that 8.5 +32 is 32mm wider than stock sedan wheels, and 8.5 +38 is 26mm wider than stock sedan wheels.

Given on my coupe I am 29mm wider at the front and 43mm wider at the rear than the 18 x 8" +30 stock coupe wheels, I would suggest that the CR Kais you have chosen should sit pretty much perfectly on your sedan. Keep in mind if you lower the car then top of your wheels leans in (which will reduce any possible tyre scrubbing), or you can run skinny tyres like 214/45 or 225/40 18s to prevent scrubbing, or you can just roll your arches a bit. But I don't think they will scrub anyhow.

To be 100% sure why don't you just trial fit them?

To be 100% sure why don't you just trial fit them?

because they are still in Japan :rolleyes:

I am thinking now about 18*8.5+32 front and 18*9.5 +38 rear as I been told from Work Australia by using

- Front 18x8.5 +32 with 235/45/18 - +5 mm outside the guard

- Rear 18x8.5 +38 with 235/45/18 - -17 mm inside the guard

I wanna rears to be flash with the guard

because they are still in Japan :rolleyes:

I am thinking now about 18*8.5+32 front and 18*9.5 +38 rear as I been told from Work Australia by using

- Front 18x8.5 +32 with 235/45/18 - +5 mm outside the guard

- Rear 18x8.5 +38 with 235/45/18 - -17 mm inside the guard

I wanna rears to be flash with the guard

as i said earlier. mine are similarly sized. your welcome to try them to ensure how they sit when you get cr kais

Hi,

I'm running Volk GT-V's on my 300GT in the below offset:

18x8 +33 (55mm dish) 114.3x5

18x9 +37 (75mm dish)114.3x5

Front offset is quite poo but never had any drama with scrubbing when I was running lowered RS-R springs on either end of car. (Now using 350Z springs)

Cheers

post-2524-0-64958700-1309067588_thumb.jpg

that needs a wider wheel or less offset, good choice in wheels though, suit it well

Agreed, on both counts.The offset is spot on for the car though.

And this our family car and the added cost of wider tyres sucks.

Something like attached look pretty good though.

post-2524-0-19550500-1309083487_thumb.jpg

post-2524-0-09029900-1309083616_thumb.jpg

ok guys, thank you very much for your replies. It makes sence now :cheers:

I am gonna buy front 18x8.5 +32 mid concave and rear 18x9.5 +38 deep cocncave Work CR-KAI but still thinking about colour options. Gunmetal is pretty dark and not sure about bronze with silver body :rolleyes:

Any ideas about colour?

34-103-CRD18858951MGM.jpg

MHG.png

DSC00302.jpg

KIF_1128.jpg

Edited by Nicko_2010

You'll hardly see the concave in the rear. There will be none up front. I'd go the 9 +17 front and 9.5 +17 rear if you want the concave

and dont buy new. heres a 8.5 +32 and 9.5 +30 for under 1k landed

http://page6.auctions.yahoo.co.jp/jp/auction/f99818646

LM is a BBS - LM wheel replica... Work vs-xx is based on BBS LM

Im with chef on this one, BBS LM's are one of the hottest wheels, Work VS-XX's are even hotter but only because they come in awesome dish... and are on my car :P

BB5 LM

18x8 and 18x9 (40mm Lip Front and Rear)

19.8.5 and 19x9.5 (45mm Lip Front and Rear)

Available Colours: Silver Machined Lip

OFFSETS : Anything from +20 to +45

STUD PATTERNS: 100 to 120 in 5 hole applications

*Photo shows undrilled wheel*

$1050 for 18"

$1150 for 19"

look like these

fuga1.jpg

Edited by SkyHi_33

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...