Jump to content
SAU Community

Recommended Posts

Big strong ones...

I've seen people with those "aircraft quality" t-bolt hose clamps, that look like they'll clamp your balls until they fall off. They're the ones I want.

Anyone know of somewhere in Sydney that sells them?

Link to comment
https://www.sau.com.au/forums/topic/36883-i-need-hose-clamps/
Share on other sites

Blackwoods sell them in SS and mild steel (coated)

Enzed sell them in mild.

Personally I dont like the clamps I have got from above stores.

First off, they have a very small tolerance on size so you have to be accurate when buying. Not a huge problem but it means you have to bring in a sample of whatever you are planning on clamping to be sure you get it right.

I also dont like the way in which they clamp up. They tend to go egg shaped and bunch the hose up a bit when you do them up and it doesnt look to me like a nice solid, airtight connection.

They are also expensive although if you can get Blackwoods trade/account rates they are about half of regular retail prices. ie $10 ea vs $20 ea.

I would like to give the clamps shown at GCG's web site a go. They are slightly different in their design and I think they may work better.

ht%20clamps.jpg

Last time I was @ Pirtek in the gong they had some BITCHIN' hose clamps. Had the outside edges trailing up so they don't cut into the hose you're clamping and the part of the clamp that actually touched the hose was inside the main ring of the clamp. Sort of a clamp withini a clamp.

If you want the toughest ones available, I would suggest going to a diesel mechanic / diesel parts supplier.

Adrian

Thanks heaps for the replies guys...

I'm headed to Pirtek in Mascot (literally in Sydney Airport), so I'm hoping they have hose clamps that will suit me...

If not, I'll try the other options listed above... Those ones pictured from GCG don't look strong enough... I'm talking about the REAL big mother bitches, like an inch-wide metal band and big-ass bolt going through it :rofl::P :P

Merli, I have the ones you are talking about, and have no probs with the hose bunching. the only thing is you definately have to buy the right size, and the tolerance is a bit low - not much room to move.

I have seen some similar to the ones browny posted up, but they have heaps of washers between the nut on the bolt and the clamp - I have these too. they are better for tolerance, in that you can fit them to a wider range of hose sizes, and 'aparently' you can actually torque them down until you distort the pipe.

I do prefer the wider clamps myself, they also have a rolled edge so you know they wont cut into the silicone hoses.

cost here in SA from around $5-8 each ($8 being for the ones on my 3" pipework), that was from a speed shop, from an exhaust shop they were about $5 dearer each.

engine.jpg

this is the best image I have at the moment, I could probably photoshop another when I get home (at work at the moment:)) - let me know?

The clamps on the BOV return are the heavy ones, I also run them from the turbo to the intercooler - the ones on the TB are the other type, with washers on the bolt. They work well too, but are thinner and dont have rolled edges.

The TB ones are available through autobarn (here in SA anyways) - they were fitted when I upgraded my IC to TB pipe, and I didnt have any of the heavier clamps on hand. Both seem to be handling 22+psi no probs.

THOSE ARE THE ONES I WANT!!!!

The ones on your BOV return pipe!!!

I'm off to Pirtek now, and if they don't have them, would it be possible for you to order me a bunch if I gave you the measurements of my silicone hosing? blowjob.gif

Should be able to work something out.

EDIT: you need to make sure the measurement is for the total diameter, including the silicone hose - they dont have a huge range of adjustment, about 5mm or so.

I will check with the local speed shop, as I am pretty sure he said he ordered them from east, see what I can find out for you.

More news, (one phone call later - big ups to Outlaw speed shop here in adeliade for all their help)

Try

High Performance World

1 Bourke st, Nth Parramatta

02 9630 2333

Outlaws said they should have them (they looked them up, as they are one of their suppliers), if not, ask if they know another speed shop in sydney

another name they suggested is Sydney Speed Shop.

If you have no luck with them, give me the dimensions and numbers of clamps you need, and I can go in and see outlaw speed shop here in adelaide and sort something this end.

I have the same clamps as 51jay

These pics show why I don't like them much.

clamp1.jpg

As you tighten them up they tend to form a D shape

clamp3.jpg

The "bunching" I was referring to

clamp2.jpg

and the lack of contact around the bolt area

I have a few 86-91mm that I want to get rid of.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
×
×
  • Create New...