Jump to content
SAU Community

Recommended Posts

  • Replies 47
  • Created
  • Last Reply

Top Posters In This Topic

I've raced an autech and it was slower then my rs4s. Maybe just a bad day for the autech but my turbo only held 10psi for 1000rpm before fading down to the poo level of 4-5psi. I think that there may be easier power making mods with the 26 but stock 25 and 26 appear pretty identical.

And hell yes rbd2 I want to see a pic

Is this the same race where you beat a VE SS Sportswagon and your boss's F6?

:rofl2:

jks!

you can easily extract more power out of the rb26 for less $$$$ basic exhaust, more boost and retune should net you 200-220awkw

same mods on a rb25 will only get you 170-180awkw.this of course doesn't take into account the difference in purchase price(which was only $5g when i bought my rs4

i know from personal experience thru the hills, the autech walks away from my stagea and we have the same basic mods, and my car isn't crazy slow either.

If you beat an autech only running 4-5psi then i suspect he wasn't really racing.:thumbsup:

Ironpaw -i understand your joking but go find yourself a ve redline ute and have a race, from 80-150/160 I sat beside him then he crept away. At 180 speed cut his tail lights were only a few meters in front of my headlights. That's the closest race I've had so far. But that said. I miss my stock turbo :'(. Stupid hypergear turbo is driving me nuts.

Big fella - I got mine 4years ago. At the yard an auto was 15990, manual 21990 and 260rs 29990. The only thing I regret is having un replaceable brake pads.

Edited by lilcrash

It drives fine, it's getting a nice consistent 7psi until high in the revs then in a matter of 300/400 rpm hits boost cut 14psi so I can't go above 5000rpm when the cams hit and my car should be going its best basically

Edited by lilcrash

It drives fine, it's getting a nice consistent 7psi until high in the revs then in a matter of 300/400 rpm hits boost cut 14psi so I can't go above 5000rpm when the cams hit and my car should be going its best basically

so its boost creeping?

why dont you get a bigger puck welded on and largen the internal wastegate.. mines currently doing it at 22psi.. hypergear said they'd do it for $120 i think.. should definitely stop your creeping issue

It doesn't do it all the time, it's like the wastegate gets stuck open then suddenly jams closed. If you move the wategate by hand it does get stuck but where the sticky spot is it shouldn't open that far.

then your actuator reach is to long.

or you dont have pre load so its already a little opened, so when it completely opens, perhaps it opens to much...thats alot of opens..

i'de be speaking to hypergear as it obviously should be happening.

He said there is no way it would reach that far. It's got about 6mm of preload

get an air compressor connected to the boost signal like to the actuator. and se how many degrees it opens.

to a shop its always a case of "nah will never do that" as they then dont have to fix theyre fault.

if your having issues like that its definitely not safe. hence the reason im on eFlex

The turbo was originally fitted with a high pressure actuator made to hold 18psi. Been told its too strong so I sent him a low pressure actuator. I have no idea how that was fitted as well as the rest of the bits. The actuator only pushes about 60 degrees out of a 33mm disc covering a 30mm gate which's not enough for it to hit the backing housing and if it does jam open then we should see very low boost.

When I sent the low pressure actuator I don't have the turbo on front of me and I don't how long the rod needs to be but longer is always better then shorter, so if its too long then just cut and thread it down to size, and 6mms of preload is way too much, should be 3mm. I don’t get how it can run 14psi then goes back to 7psi. I have a feeling some of the vacuum plumbing is a bit strange or it is too much actuator preload. I'm guiding a novice DIYer and its pretty hard work. :/

The car's needs injectors and a tunned for 18psi. Its not going to make much more power with stock tune and factory boost. And have to say its doing pretty good keeping up with a RB26dett stegea.

I'm in no way a novice DIYer. Most of my job is custom fabrication.

The high pressure actuator gives in stable boost as the wastegate is held open.

There is no vacuum out put on the turbo outlet so I have used the nipple on the next piece of pipe to the intercooler.

Next point. It's got 6mm of preload because that's all the thread that's on there, at 3mm preload it barely had any boost.

I only wish to run 10psi until I get the other parts.

JUST SO EVERYONE KNOWS. THE ATR43SS-1 THAT I GOT FROM HYPERGEAR ISNT CAPABLE OF LESS THEN 16/17 PSI. SO BEWARE.

Edited by lilcrash

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...