Jump to content
SAU Community

Recommended Posts

hey there guys. got defected for being to low the other day and need to get a roadworth. before i went to take it in i gave it and the engine bay a wash. i then backed it out of the wash area and into the garage. about 10 minutes later i went to take it for a drive and it had a miss at idle. i went to keep driving it as i was heading to a workshop anyway only to have the car almost die when i went to drive off. and didnt improve at all down my drive. so i took the car back to the house. its a series 1 r33 gts with the only engine mod being a k&n pannel filter. any suggestions on what the problem might be. thanks

Link to comment
https://www.sau.com.au/forums/topic/369131-r33-gts-missfire/
Share on other sites

Depends on what the problem is. If it is a missfire as in the a cylinder is missing a spark and causes the engine to make a noticeable jump then your coilpacks need to be replaced. This is likely as your coilpacks are pretty sensitive (shock, moisture). Also depends what else you got wet and how the engine is behaving so try and give us some more details.

the car runs great first thing when the engine is cold. as it starts to warm up it starts missing at low revs. the hotter the engine get the worse it gets at higher revs. so when it first starts to warm up the car runs well when travelling at 2500 rpm but almost stalls at idle. then when at operating temperature the car misses badly at revs and only slightly at idle. will be checking coils.and plugs this morning

It'll get better over time but it'll wear the f**k out of your engine.

Pull every spark plug out, dry out each plug/where it plugs into.

Make sure none of them are f**ked. You may want to grab a piece of fine-grit sand paper and clean up the sparking parts of the spark plugs.

Then, you need to get in your car, drive down to the local mechanic, tell him what you did and let him fix it.

Running worst when warm reminds me of my coilpack issue... i covered it in silicon however I'd recommend you leave that resort till last. You want to attack the immediate problem as opposed to imminent problems.

But yeah tbh I wouldn't even bother touching the car myself.. your mechanic will have all the replacement parts and knowledge you need to fix this.

Edited by SKITTLES

geez i really cant remember the voltages but if you had a power fc it would tell you automatically. There's a few posts that explain which terminals are which and what the correct volatges are. Not too sure if you should bother with this one, basically the car wont be able to hold idle and will just die if the afm is ruined.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • Bunnings would have just handed you your money back on that one!
    • So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...