Jump to content
SAU Community

Recommended Posts

White 96' R33 GTST, immaculate condition in and out no dents or scratches!

96,500km's

Manual

Turbosmart dual stage boost controller (hi-lo)

APEXi S-AFC II air fuel controller

Full HKS Superdragger exhaust, 3.5" mandrel bent with high flow cat

Blitz BOV

Heavy Duty Brass Button Clutch

Hicas 4WS

HKS Type 0 turbo timer, displays volts etc.

Autometer Boost guage mounted on A pillar

Dual Stage shift light

Nismo Gear Knob

HKS Pod Filter

Short Shift Kit

Strut brace front and rear

Racing Pedals

Red VHT sprayed Calipers

Series II Bodykit

Koni height and damper adjustable suspension with King Spring low's

17" BSA Racing rims 235/45's all round, brand new Dunlop Leman's tyres on front

Full central locking and 3 point imobiliser alarm

Dual airbags

Hicas 4 wheel steer and ABS brakes

Receipts for many of the above mod's, Lots of money spent!

Can be included, competition stereo. Pioneer double facing head unit ($1400), 220W Pionner front splits with tweeters and 300W 6X9's in Rear. Speakers powered by a 480w pioneer amp. Two 12" SPL Competition square kicker subs in box in boot powered by a 1000W Crossfire amp and crossfire sub control switch mounted under stearing column. setup worth $5000 legitimately can provide model numbers of every component if you would like to check.

Extra's: Tommy Kaira Wing sprayed same colour as car, White faced colour changing EL dials and blue axs seat covers.

$24,900 ono contact via email [email protected] or pm me.

im in noosa about 2 hours drive from gold coast....if your genuinely interested pm or email me and we can talk further.

Add me to MSN mate. I got a bruz in Dickie beach, mate. My bruz said its about half an hour or so to Noosa. He said he can check out da car man.

[email protected]

Add me to MSN mate. I got a bruz in Dickie beach, mate. My bruz said its about half an hour or so to Noosa.  He said he can check out da car man.

[email protected]

thanks for the interest JOSH......you have far to much spare time on your hands :D

anyway...car is still fs, so come on people

looking at 24,900 with sound system, its genuinley worth around 6000 installed. If your interested pm or email me and we can talk further. The plates will most likely sold with the car, until its sold im going to keep them.

Car is still available, I thought it was sold today however it fell through. Anyone interested feel free to pm or email me. Cheers Matt

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lets say I wanted to buy this, specifically for this purpose. How do I actually perform the function. Can I still buy a Consult-1? Am I about to be burned by the fact my car is a 2000 model Series 2 R34 and thus will be some stupid other system? Do I just need this -> https://obd2australia.com.au/product/nissan-consult-14-pin-to-usb-ddl-diagnostic-interface-with-ftdi-ft232r-chip/ And with what software?
    • That's probably OK. That's a face to face compression joint between two surfaces with the clamping load provided by those bolts. So.... it's unlikely that the bolts will end up feeling that load in shear, unless the clamping surfaces are not large enough, bolts not got enough tension on them, etc etc to prevent the two faces from moving wrt each other. Which... I would hope the designers have considered, seeing as it's probably one of the most important things the upright has to do apart from resist collapsing in its own right. But yes, it would definitely be worth asking them what their safety factor on that part of the design was. I tend to think that the casting, being a casting, is not necessarily the strongest bit of material in the world. It's about an inch square, and when you think about the loads that are being put into it, you have to wonder what safety factor the Nissan boys (and every other OEM engineer who has designed all the millions of other uprights that look essentially the same) used to account for defective casting, aging, severe impacts on the wheel, etc etc. 
    • Those bolts would be orders of magnitude stronger that cast aluminium though.  And its mainly clamping force, not shear they are dealing with?
    • Except all that twisting force that is breaking a cast piece, appears to be going through 4 bolts in the picture Johnny posted of the BryPar one...
    • The smart approach is to use the gearbox loom from the manual car. Makes it a lot easier - just plugs into the switches on the box and plugs into the main loom up near the fusebox. Then you only need to deal with bypassing the inhibit switch. The other approach requires you to use the wiring diagram to identify those wires by colour and location, perhaps even indulging in a little multimeter action to trace them end to end to make sure, and then.... you will have the answers you need. The R34 wiring diagram is available on-line (no, I do not have a link to it myself - I would have to do a search if I wasn't able to go to the copy I have at home).
×
×
  • Create New...