Jump to content
SAU Community

Recommended Posts

Stealth means asking on an internet forum..................hahahha.

Try mounting your switch under the dash somewhere? But one thing you don't want to do is have a switch that you have to bend to use - you need to be in your normal driver position and still be able to access it otherwise you'll look like your using a kill switch

I have a kill switch off the ecu area and I also have a battery isolator switch on a remote. My alarm - you could say - is direct feed to the battery so it is unaffected.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901327
Share on other sites

i wouldnt discuss a kill switch on here, they can be so stealth you cant see them or touch them. RFID chips . Iphone bluetooth, IP the list is huge, it depends on your budget and know how.

not many places in OZ know how to do a RFID or proximity kill switch. that I have found. anyhow

kill switches can as easy as a cig lighter or something you never touch just your "presense" is all you need.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901602
Share on other sites

Stealth means asking on an internet forum..................hahahha.

Try mounting your switch under the dash somewhere? But one thing you don't want to do is have a switch that you have to bend to use - you need to be in your normal driver position and still be able to access it otherwise you'll look like your using a kill switch

I have a kill switch off the ecu area and I also have a battery isolator switch on a remote. My alarm - you could say - is direct feed to the battery so it is unaffected.

thats the first place a crim will look, and a huge fail !!! and you just announced how to defeat your alarm to the world

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5901607
Share on other sites

a crow bar fixes that, and most of the time theyll break into the boot looking for easy to take items if they can't start the car

then your car gets ransacked , best bet is to stop them BEFORE THEY BREAK IN using common sense

then a mutiple layer protection

and ultimate a GPS interface that can remote shut off the car next time the brakes are applied below a set speed, or geofence

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5904682
Share on other sites

hate to say it but the last few 33s I have repaired from theft the boot was popped the pump relay bypassed and then the column smashed.

insurance is the best idea. some of the cars I do have remote relays on them and if they do not see a remote control signal they DO NOT work. google that. plenty of companies make them.

Link to comment
https://www.sau.com.au/forums/topic/370228-killswitches/#findComment-5906555
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • all brand new unit from Tomei, fluid, bearings, etc. Tomei said they call it a 1.5 lsd because its 100 percent lock up under acceleration and 50 percent under deacceleration.  as I mentioned I used their fluid, install and their break-in procedure, (alot of figure 8's) but even when driving straight, or even slowly backing out of garage for first time, (at 2 mph) then driving to and from figure 8 parking lot, each tire in the rear would sporadically grab, skip, bounce, shutter and skip, shutter back a force I could feel causing clutch to slip then grab, at any speed. shaking entire car. I removed unit, since I put stock back in and all is fine, via process of elimination, its something with the lsd unit itself. I wasn't going to beat up the entire car more or change anything else for no reason as I had a feeling something in the lsd itself was wrong as everything was fine before this alone was installed and I rechecked over everything else after first time backing out I suspected an issue. I'll probably sadly already need new tires now just from trying to drive it 5 miles and performing the figure 8 break in. but if someone has any ideas I'm all ears 
    • Ok thanks..that was my second question if i can somehow bypass this even with Nistune(that is all i have right now...aparat from stock ECU. So with some aftemarket it can by "bypassed" or make it work?  I know there is Link or Haltech (mainly used). We have ECUmaster here so i will gather some info about it.
    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
×
×
  • Create New...