Jump to content
SAU Community

Recommended Posts

Hi guys, Im thinking of putting on a nistune on my r34gtt... Mods are: full exhaust, fmic, walbro fuel pump, greddy ebc 10 psi, all the basic mods... How much wil it costs me?? And a good place to install nistunes?? Im from the west btw.. Cheers

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5905731
Share on other sites

if you can grab a lift over, you can leave it the night before and then pick it up the following arvo. It's not that far a walk from dandy station, and i'm sure there is a bus that goes closer.

i would "think" they would only need 1 day to get it done, so you could prob just hang around whilst it's done if you've got a free day somewhere

Best to ask them though.

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5905967
Share on other sites

if you can grab a lift over, you can leave it the night before and then pick it up the following arvo. It's not that far a walk from dandy station, and i'm sure there is a bus that goes closer.

i would "think" they would only need 1 day to get it done, so you could prob just hang around whilst it's done if you've got a free day somewhere

Best to ask them though.

Thank you for your kind help.. I will give them a buzz tomorrow..

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5905973
Share on other sites

Yes charles, you're right... But ill give chasers ago... Been their customer before, i think they will do the job right... Well, its time to find out next week.. Cheers to everyone .. Been really helpful...!! I will update the results..

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5906117
Share on other sites

Oh yeah, no doubt, Chasers, Dr Drift & Chequered Tuning are all reputatable, so any one of those should be just fine.

And yeah, let me know your results, coz I wanna get mine done too :P

No probs.. I saw u selling ur nistunes daugtherboard, why dnt u used it?? I actually txt u for ur power fc and askd u bout the wing stays as well yesterday... :)

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5906158
Share on other sites

Oh haha xD

Yeah I sold my board, because I got the board as a payment for a job that I did for someone, and I think Chequered wanted $50 to install and $650 for a tune, so it woulda cost me $700. Where as, when I sold the board for $250, I only need to add $600 on top for a drive in drive out deal at Chequered for $850 :)

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5906166
Share on other sites

Oh haha xD

Yeah I sold my board, because I got the board as a payment for a job that I did for someone, and I think Chequered wanted $50 to install and $650 for a tune, so it woulda cost me $700. Where as, when I sold the board for $250, I only need to add $600 on top for a drive in drive out deal at Chequered for $850 :)

Nice... :)

Link to comment
https://www.sau.com.au/forums/topic/370474-nistunes/#findComment-5906214
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...