Jump to content
SAU Community

Auto Electrician

aky

By aky,
in New South Wales

 Share

Recommended Posts

aky Rookie

aky

Posted
Posted (edited)

Ok guys need a reliable auto electrician to come and have a look at my R33 as i think i might have damaged some electric parts when trying to jump start the car yesterday. I put the cables the wrong way (i know stupid, but hey shit happens) and had some smoke coming from inside the car dashboard. The car does not start at all, it will not even crank, all other electronics work in the car if the key is put in ignition.

So yes anyone can recommend an electrician that will not charge an arm and a leg that could come to my place and have a look at it.

Location: Merrylands

Edited by aky
Link to comment
https://www.sau.com.au/forums/topic/370475-auto-electrician/
Share on other sites
aky Rookie

aky

Posted
  • Author
Posted

Checked the fuses in the boot, they look to be fine. I was thinking of maybe taking the fuses to supercheap and getting a new battery, then replace them all and see how it goes. But would still need an auto electrician in case that does not work.

aky Rookie

aky

Posted
  • Author
Posted

Went to chk the fuses under the dashboard 2nit, thought to my self lets see if it turns on, surprise surprise it turned on and i took it for a little drive everything looked fine. Parked the car then tried to start it again about 30min later and it will not start, but it at least it makes clicking sounds now. So now i am thinking that it might be the battery that is dead, so will get a new battery tomorrow and will see what happens.

aky Rookie

aky

Posted
  • Author
Posted

Bought a new battery, put in and it started without any issues. Took it for a drive all good, started the car after 30 min again and its still starting without any problems. So it looks like the battery was the problem after all, the other battery was all watery when i took it out so must have damaged it when trying to jump start it. So relived thought i might have done some serious damage to my car.

  • 4 weeks later...
SargeRX8 Grand Master

SargeRX8

Posted
Posted

Nerds lol

I had smoke come from my blinker switch today... Can't be good ay lol

Your relay/blinker might be on its way out. Smoke is never good. What is it? Unless its a fuse melting(which is very unlikely as they designed to blow, unless you put a higher rated 40a fuse in a 5a slot) it is most likely the wire casing melting. This isn't good. One second is nothing, but 3 - 5 seconds is enough to get rid of the plastic and leave bare wire exposed which can cause havoc. My mates ford laser smoked for about 3 seconds, he used the wrong fuse which didn't blow and allowed too much current through. The end result was a bundle of wire with minimal shielding literally melted together. He traded the car in the next day.

I'm pretty handy with electronics, if anyone needs help, I'm near Parramatta and can see what I can do. Ive fixed all issues both electrical and mechanical in all my cars and helped my brother rig up two of his cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      Any idea where I can get genuine MAF apart from used ones? I can't find any only for GTRs and unfortunately that price is not in my budget 🤣 I might gap my plugs down and put my splitfires in, they were only in for a year or so before I started the rebuild 
×
×
  • Create New...