Jump to content
SAU Community

Recommended Posts

Perspex sucks!!! I got it from bunnings.

If you can get polycarbonate/lexan, that material is less likey to shatter.

I cut it with a bandsaw at bashers workshop, the inside ring, I just drilled a crap load of holes with drill then used the drill to cut between the holes.

Then just gave it a quick file. It's rough, but beats paying $1200+ for nismo's.

Cost:

housings $250 (I didn't want to pull mine apart)

perspex $35

90 LEDs $78 (jaycar electronics)

resistors and diodes $4

silicone $12

I'm hoping the will be bright enough! In hindsight I should of tried the brake lights in the sun to check brightness....

Thanks for the break down.

I've got plenty of housings which is good :D

Where did you buy the LEDs?

My usual spot for random things is eBay, but someone recommended in the thread not to.

So cheap on there.

What MCD LEDs did you go for? - you're hoping they're bright enough! Let me know haha.

From jaycar, and they are 4000MCD.

Lol, I put in in the last page of my post....

Cool, yeah I had a brief look in ebay..meh

My tip for the day is keep an eye on the oven, if you smell plastic....RUN lolz!!!!

  • 6 months later...
  • 1 year later...

I see you printed the circuit boards for your LED Taillight conversion was it difficult?

http://zilvia.net/f/showpost.php?p=4694490&postcount=21

dsc00766.jpg

Can you make some for the R34?

  • 4 months later...
  • 3 weeks later...

Making good boards like this is pretty easy if you have the right tools ,

Sneaky trick running 3 LED's rather than 4 in each string allowing the brightness level between Tail and Stop to be a reasonable contrast.

I'll be placing some LED's up the rear pillar on my Axis this weekend if I'm not on the road, so I had best take some pictures as well :)

.

Edited by MozzMann

i was thinking about doing it mass produced wise, had the patterns all stored in the cutter and everything and and even have a 70% finished set sittign in my room with male adapters for the factory plugs.. so much CBF though

  • Like 1
  • 2 weeks later...
  • 6 months later...

Has anyone used Red LEDs instead of the clear ones in their tail lights?

The current prices at Jaycar are -

White waterclear LEDs 4000mcd = $1.90/25+ LEDs, x100 the total is $190

Red waterclear LEDs 4000mcd = $0.99/25+ LEDs, x100 the total is $99

(correct me if I'm wrong)

My understanding is that only the red light produced from a white LED is going to pass through the stock red tail light lense. Where a higher percentage of light from a red LED will will pass through the red lense.

So in saying that, would a red LED should be perfectly fine behind a red lense?

  • 1 month later...

Has anyone used Red LEDs instead of the clear ones in their tail lights?

The current prices at Jaycar are -

White waterclear LEDs 4000mcd = $1.90/25+ LEDs, x100 the total is $190

Red waterclear LEDs 4000mcd = $0.99/25+ LEDs, x100 the total is $99

(correct me if I'm wrong)

My understanding is that only the red light produced from a white LED is going to pass through the stock red tail light lense. Where a higher percentage of light from a red LED will will pass through the red lense.

So in saying that, would a red LED should be perfectly fine behind a red lense?

Any update on your LED DIY?

IME using white leds behind a red filter will give a pinkish red. Its not a proper brake light colour at all. Much better to use red leds in the first place.

Also those prices at jaycar are criminal. No way is a single 5mm led worth $1.90 per led (bulk price too!). I dont even bother with jaycar anymore unless there is a single item I need right away, the prices are far too high.

I have found regular lensed leds to be quite reliable from china off ebay. We're talking 100 of them for about $2. As long as you drive them conservatively, perhaps <50% of their rated current, they should be fine for many years.

I have never had a regular lensed led start flickering (and eventually fail), unlike SMD leds which I have seen many times.

I suspect part of the issue is that ebay led light packages come with too low resistors, and so the lights are being driven harder to be made brighter, but at the expense that a higher % of them will fail.

Any update on your LED DIY?

No not as of yet, car has been at my mechanics for many months so I haven't had a chance to get started on it. I will be doing a Nismo R34 led layout on an early tail light (afterburner) HR31 Skyline.

  • Like 1
  • 1 month later...

No not as of yet, car has been at my mechanics for many months so I haven't had a chance to get started on it. I will be doing a Nismo R34 led layout on an early tail light (afterburner) HR31 Skyline.

Let me know when you start working on this R34 LED project

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...