Jump to content
SAU Community

Paintless Dent Removal...

Kevs

By Kevs,
in Western Australia

 Share

Recommended Posts

Kevs Contributor

Kevs

Posted
Posted (edited)

Hey folks

I have a few those little dents on my car caused by careless assholes who hit my car with their car door, it wasnt so upset if that was on the door but it happens at my rear quarter panel. i need to get rid of asshole dings on my car, so I was wondering if you guys have any experience on the paintless dent removal? any experience? do they able to repair? and was it a worth try?

Cheers

Edited by Kevs
Link to comment
https://www.sau.com.au/forums/topic/371271-paintless-dent-removal/
Share on other sites
R32 TT Mentor

R32 TT

Posted
Posted

Have had it done on my car a few years back and seen it done on others. If you get the right guy, un-be fkn leivable. Seriously I had a cracker dent put in my HSV and you could not tell it has ever happened when they had finished. Really, really impressive.

I am going to get a couple of shallow ones taken out of my GTR soon too.

confuzion Community Regular

confuzion

Posted
Posted

I personally used the Ding King on my STi when someone kicked the front 1/4 panel in and he got it out - could never tell it was there..

Actually I think there's still a pic of the dent on there - http://www.thedingking.com.au/images/custom/sub3.jpg

Wasn't too expensive either, $150 or so from memory and highly recommended.. I will be using him for my r33 to get a rear 1/4 panel dent out soon

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • nash47
      Cas issue

      By nash47 · Posted

      Did and sync timing with light 
    • MBS206
      Cas issue

      By MBS206 · Posted

      Have you done the Ignition Sync Wizard in the AEM software?
    • MBS206
      R32 GTS (RB20DE) Injectors Replacement

      By MBS206 · Posted

      Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • MBS206
      RB25DE NEO with Haltech ECU

      By MBS206 · Posted

      You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...