Jump to content
SAU Community

Recommended Posts

Not at all.

Solar is worth it but you have to be prepared to spend up on a bigger system. 1.5kw systems are useless. When purchasing solar, go the biggest you can possibly afford, and then beg borrow and steal to go a bit larger again.

The average household uses ~20kw/h per day. A 1kw system (in Vic) will generate, on average, 3.5kw/h day. So a ~4kw system will produce around 14kw/h day. That's near enough to 75% of the average daily household, so a 75% cut to CO2 output from home electricity use which is significant.

From a financial perspective, it depends on where you live. In Victoria, you get a premium feed in tariff for every kw/h you export back to the grid. So the inverter on the system is wired into the switchboard which means your home will use the power first, then excess will be exported. This has the extra affect of encouraging households to reduce consumption. So not only does it produce CO2 free power (average 75% of a homes usage) it also encourages households to reduce usage.

As an example, one system I sold went on the roof of a home of four (2 adults, 2 children) which had an average use of 14kw/h day. Since it went in (just over 12 months ago) it's offset their entire electricity and gas bill AND seen them receive around $2,000 in refunds from what they exported. Their system is 4.08kw and cost ~$13000. So return thus far is around $3500-$4000 for the year. That will slowly fall off, but the system will pay for itself in around 4 years. After that it's ~$3,000pa return. Not bad. And CO2 is reduced significantly.

Each state has it's own rebates and tariffs, so this above is for Vic. You're in Shellharbour, is that SA? I believe they have a $0.40 feed in for exported, similar to Vic. NSW had a gross feed in tariff which was just stupid. All generation was paid at 60c for systems up to 10kw. It was unsustainable and did not encourage reduction in usage and resulted in an explosion in installs, many of them dodgy. A 10kw system in the right spot could return you $15,000 pa which was never going to last.

My recommendation for anyone installing solar is the bigger, the better and pay more for a reputable company. Also, German and Aussie made does not mean good, it means expensive. Go with Chinese panels. They are as good as any and half the price. As for inverter? That's tough. Aurora, SMA, CMS, Aerosharpe(if on a tight budget), Xantrex and there are probably one or two other decent ones on the market now, but they are the pick.

EDIT: I see you're in NSW. The Premium feed in tariff is no longer available, so solar is questionable from a financial perspective. Environmentally, yes, financially you're looking at ~10 year pay back, which still isn't terrible, but it's not great.

Edited by Cowboy1600

Thanks for the info :).

Yeah new so I might have to stretch the truth, Base my talk as if it still has the 60c rule. My dad has the 60c rule then got more with the 0c rule hah. All they do is turn back our clock.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for posting, your engine bay looks tops. I'm fairly sure you posted the wrong video though, I think you were supposed to upload the one from your "private test road" where it's banging off the limiter with the gate open?
    • This is something to be careful of. I did a bit of digging on the NM35, as I spend a lot of time on near brand new cars and CANBus related stuff, which uses the same "OBD2" plug for a fair chunk of making my life easy. The NM35, does NOT support OBD2. The data pin is actually on Pin3, which is a manufacturer specific pin, and requires Consult3 to connect to the NM35. Your low voltage, is either because the NM35 doesn't have 12V to the constant power pin on the J1962 (OBD2) connector, OR, it is attempting the standard comms, (CanBus, K Line, etc) and can't see any voltage on those pins. Some people have had success accessing SOME data from the vehicle on OBD2 specification, using a module that supports KPW. My assumption, like Duncan has stated, it will likely actually be JOBD, where there is some cross over with the OBD2 and JOBD standards. Note, lots of "OBD2" dongles, do NOT support KPW, which is what you need for a lot of Japanese vehicles of this era (And even up until recent years!), EG, Subaru, Suzuki, etc.    The end of this thread is probably worth a read, as some people did find a way to get a display up in the NM35 recently, looks like someone implemented all the stuff needed to make it work. (The right protocols).  
    • Depending on the purpose of the car, and how much more fabbing you want to do, and what clearances you have, you could look to raise the motor, which will raise the front diff up. Likely would mean altering the chassis rails etc etc, hence the more fab work you'd need to do. However, this can create issues, not just in clearance with everything fitting under the bonnet, but you've also raised a LOT of weight up in the car, and this will DEFINITELY alter handling characteristics (But, so will how much weight you've already added to the front end). You'll also have to deal with the fact the gearbox to rear diff is now out of alignment too for the tail shaft, and alter the angle of the diff, or deal with a bit of potential vibration. Raising the motor an inch up, is effectively the same as making the whole car sit higher by not lowering it as far. So one inch higher motor, theoretically means you can drop the car an extra inch lower, and maintain the same angles in the CVs. Again, depends on the purpose of the car. If it's a just cruiser on the street car, maybe won't be an issue. If it's meant to be a time attack car, I can see you not wanting to raise the motor. This is just for you to ponder as an idea.
    • Have you not seen geospy.ai? It can now give GPS co ords to within a metre from a photo, even if it's a random photo you take inside. Supposedly at the moment only the government/law enforcement has access to that... Supposedly...
    • I've got the rear ones, they're certainly beefy. I need to take them to my driveshaft guru to check over, he's very fussy about the quality of components so I'll let you know if they are made of cheese by a blind man.   Are you in Australia? A mate just had a set of EN26 shafts made for his K20 Lotus by our fabricator which were quite cheap (compared to Driveshaft Shop) so if you can procure the CV's and draw what you need he'd make them for ~$800 for the pair.
×
×
  • Create New...