Jump to content
SAU Community

Recommended Posts

It sounds like alternator whine. These get into your system via ground loops that are usually caused by dodgy earths or having RCAs too close to power wires. They can also be caused by cheap gear or a faulty alternator etc.

Have you just had new stereo gear fitted or did the noise just start up for no reason?

What type of system do you have?

The gear is fairly new about two months old. I have a JVC top of the line deck, mtx splits and jL sub and amp. It was running fine for a while and now the noise. I do have a noisy starter motor on start up though, could it be that? I also had problems with the amp causing my 4wd light to come on...

Mick

my amp is mounted right next to the battery and the fuses ect and i found when i move the amp away from there it becomes less of a problem.

i also tried buying some of those streetwires rca's about $40 for 1 and that just made the problem worse, go figure. i even ran the rca's on the outside of the car to see if that would work no go.

u can buy some kinda of thingo that u attach to you alternator and its ment to stop the whine

check to see if your earth is ok, try and keep RCA's as far away from power cables as possible, it's ok if they cross... i don’t see why having the amp in the boot would be a problem, i have a 1600watt amp in the boot and run 4 gauge straight from my battery and had no problems.. never seen my 4wd light come on

u running the front speakers off the amp or deck?

check your suppressor of the alternator, make sure all wire casing is intact, your amp cables should run down one side of the car, your speaker wires the other and your switch wire down the guts, try to keep all wires away from car wiring , make sure you have positive earth conections. 4wd light no idea sorri

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • That's convinced me I'll bump up the G30-660 to 770   Any idea if the difference in boost pressure? Cheers
    • When: Saturday 24th of May 2025 - All day Where: Sydney Dragway, Eastern Creek Cost: Varies - Book direct with the GTR Festival Website We will be there on the day with a stand please reach out via our interest form if you wish to help out with the stand. Limited parking will be available in the display area, first in first served with current members getting priority, please register your interest with the link above also. Please post any great photos you take on the day on this thread and we will try use some in our e-mails/website/social media
    • Hey guys so turns out this project is going to be much bigger than I thought haha but I've done some my homework and have done a few panels on my car, but one part I can just not visualise is this. If I do a spot repair and I put filler in a dent for example and sand outside of the repair with 320 grit lets say so the primer can stick as I will only put primer on that repair and the surrounding area and then repaint the whole panel. Don't I need to make sure that I don't put primer on the old clear coat? I keep seeing YouTube videos where people have new paint and primer land on the old clearcoat that isn't even dulled down, it's still shiny. I thought putting paint on clearcoat or primer on clearcoat is a bad idea because it won't stick. So in this scenario it's a bit different to mine but imagine someone doing a spot repair and only painting that small section of repair but the new paint is landing on the old clearcoat. What am I missing?
    • I was immediately reminded that your location is QLD. Sounds like a perfect SEQ business idea.
    • And if you can't drive bigger injectors with peak and hold as low impedance injectors during low pulse width, it's even harder to get a nice clean known amount of fuel.
×
×
  • Create New...