Jump to content
SAU Community

Stolen Silver 180Sx, Black Bonnet, Blue Side Skirts


Recommended Posts

Stolen silver 180sx, stands out - black Bonnet, blue side skirts, territory wheels on back. Lots of Sticker. Micks old 180sx from All Performace Garage. stolen from Broadbeach Waters between 8pm - 1am. Any info please contact Zac on 451070389 or Police, thanks.

Number plates may be different to the ones in the picture below, will update post as more info comes to light.

198632_270872032926803_202834106397263_1266489_896423_n.jpg

Edited by GHOSTrun

How do these cars keep getting stolen? This is getting closer and closer to home and I want to know what (if anything) was protecting these cars from theft in the first place... Surely they can't be getting past immobilizers, alarm systems and fuel cuts (yes I understand they can simply load it up on a truck, but not from lock garages)? Sorry to hear another innocent victims car has been stolen :(

Edited by Reflector

I'm wondering the same thing myself. if half these cars had full alarms on them properly installed I dare say that most would still be sitting in one spot still.

How do these cars keep getting stolen? This is getting closer and closer to home and I want to know what (if anything) was protecting these cars from theft in the first place... Surely they can't be getting past immobilizers, alarm systems and fuel cuts (yes I understand they can simply load it up on a truck, but not from lock garages)? Sorry to hear another innocent victims car has been stolen :(

Often wondered that myself. I asked my alarm installer how long it would take a thief to defeat an alarm system and he said if the alarm install is bad, can take 1-2mins to bypass, if it's done well, still only 5-6mins to bypass, this is of course assuming the thief knows their stuff.

Steering wheel locks (i.e. club locks) can be defeated in 30-90seconds with a puller type device readily available to anyone to buy off the internet (they are marketed towards repo guys). So although a good deterant, don't put too much faith in them.

Kill switches, if the thief knows what to look for they can usually find where the owner has put them with a bit of common sense, or they just bring their own tools to manually bypass them, working out what needs to be overcome i.e. fuel/spark etc.

CCTV footage doesn't stop the car from being taken, and in a lot of cases even if it shows the thieves it doesn't mean jack shit to the cops because they can't properly identify the culprits and/or don't have them in custody.

IMO the only safe bet is to have full comp insurance and GPS tracker installed stealthily if you want any (real) hope of retrieving the car, and to try and park it in a secure place.

Edited by GHOSTrun

Saw something like this tonight at about 7:45 headed north on Gympie road. It pulled into the Shell/Maccas on the corner of Newmarket. Was same colour. Dark bonnet. Didn't see wheels or skirts. Plates were different. Had 030 in them. Tint seemed darker also.

If it was the same car it looks different now.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
    • Literally looks like direct port nitrous haha
×
×
  • Create New...