Jump to content
SAU Community

Recommended Posts

Turbo and intercooler bypass (D-valve)

A method by which a large zero cracking pressure one-way check valve is inserted just prior to the throttle body, enabling air to bypass the turbo, intercooler, and piping during periods where there is negative air pressure at the throttle body inlet. This results in more air combusting, which means more air driving the turbine side of the turbo. As soon as positive pressure is reached in the intercooler hosing, the valve closes.

Sometimes referred to as the Dan Culkin valve.

When used in a MAF configuration, the D-valve should draw air through the MAF to maintain proper A/F ratios. This is not necessary in a speed-density configuration.

thats pretty cool, very passive system, wonder how well it would work.

Evos have factory antilag, but having it on anything else would be impossible to get engineered short of a drive cycle test, in which case it wouldnt effect the reading(depnding how it was setup)

...Strange eh.

tmk they have the air bypass hardware but not the required ECU mapping.

I can't imagine any manufacturer that offers warranty leaving this "feature" enabled.

Cheers,

SW

I setup antilag on the Vipec for shits and giggles (it's not 100% setup as I'm not that keen on it). Definetely not good for your car though.

You sure Evos have it from factory? What models? I've never heard that before that's all.

You mean proper antilag for between gear changes or just launch control antilag? (I wrote up a post in the past explaining all the different things people refer antilag to but can't be bothered finding it).

How did you set it up exactly? I heard they install a fuel injector or something into the exhaust mani?

Have you also setup the launch control or flat shift?

How did you set it up exactly? I heard they install a fuel injector or something into the exhaust mani?

Nah you don't install an extra injector. It just retards the timing by a huge amount and opens the injectors to create a lot of unburnt fuel so it can ignite in the exhaust manifold. It's all just settings in the ECU.

Have you also setup the launch control or flat shift?

Nah havn't done that yet. Launch control is something I want to setup in the future though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
    • Hi @Chupapy i had several leaks from coolant pipes being corroded, i also had one leak on back of the head onto transmission. For me that leak was from the turbo water line. Follow the line to the back of the head The hose and metal pipe had perished these are the best pics I took of it at the time
×
×
  • Create New...