Jump to content
SAU Community

Rb25, Rb30, Td06, Os Giken

Buckna
 Share

Recommended Posts

Buckna Community Regular

Buckna

Posted
Posted

Alright, have a few things to sell, all this was going to go into my latest project but I have bought a new engine setup for it now.

Have, rb25det. complete inlet and exhaust side, missing turbo, has Greddy adjustable exhaust cam gear, full loom and ecu, loom has been modified previously, suit conversion. has coilpacks, injectors, etc.

Timing belt idler was a little noisey, so has been pulled off and is awaiting a new timing belt, haven't done this yet.

$1000 as is, or $1200 with new gates timing kit installed.

Z32 300zx gearbox (same gearset as RB25 r33 gearbox) with RB25 bellhousing on it, ready to bolt to RB20/25/30. good condition.

$1000

OS giken twin plate clutch, still heaps of meat left on it. comes with flyhweel, clutch plates, intermediate plates and pressure plate. good clutch. retails for around 2.5k

$650

Trust TD06 25g. Have the big td06 also, just been rebuilt, new bearings and seals, T3 footprint 16cm exhaust housing. great condition, will easily go over 500hp.

$1000

Nitto 40mm wastegate, brand new, all flanges included.

$150

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

Can include full reconditioned RB25 head, 1.2mm metal headgasket, head modified to suit RB30 block, cleaned, decked, valves ground and seated, vacuum tested. Assembled on engine,

$1700 complete assembled RB30/25 motor.

BMW E36 318is Getrag 5 speed gearbox and clutch setup, Unneeded, box is perfect, clutch looks ok. Can come with twincam engine as well.

$700

All located brisbane CBD. contact buckna. 0427282562

Link to comment
https://www.sau.com.au/forums/topic/373987-rb25-rb30-td06-os-giken/
Share on other sites
tridentt150v Grand Master

tridentt150v

Posted
Posted

Forged RB30 bottom end. ACL forged pistons, block bored to suit, crank linished, new bearings all throughout, RB25 oil pump, RB30 new waterpump, New rear main seal, comes with sump, ring gear, balancer, timing case. Ready for either RB25 or RB30 head.

$850

what rods?

riley Collaborator

riley

Posted
Posted

still have the rb30 block? price shipped to darwin 0830? is the block all inclusive ie. pulleys, sump, crank,etc...

keen as to buy for a 30/26 convo. will have shipped to ballistic customs.

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      Ok so will run the piping over that radiator and no plenum it is. Put that money towards a Haltech and see what suits. Any ideas something like an elite 2000 or 2500 right? My long term goal is 300kw e85 and manual swap and that’s a dream come true. For now will be 200kw and auto the stock rb25det neo intake isn’t too expensive with throttle body. If I was to have the port matching done, Would that be better than the stock de intake as the det has bigger holes plus has the spots for sensors etc? And suit more long term?  appreciate the advice?   
    • MBS206
      R33 GTR running -9 with no tune

      By MBS206 · Posted

      You understand AFR is not the only thing that contributes to it pinging yeah? Funnily, what the AFR gauge will tell you when it likely is pinging, is going to make you think things are really safe and good.
    • MBS206
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By MBS206 · Posted

      Run the piping how we all have for decades. Also the duel runners with the +T setup dramatically helps it gets on boost quicker. Yes, chase huge power it'll become a problem, but you're a long way off when you're already saying an aftermarket ECU is out of the budget. You also say NisTune as it's simple, and then immediately say it'll be painful, meaning... It won't be simple. It will likely cost you a lot more stuffing around with a Nistune, than just putting a Haltech or similar in.
    • 677_GTR
      R33 GTR running -9 with no tune

      By 677_GTR · Posted

      I’ll order an afr gauge to keep an eye on it.  Then will get a haltech soon 
    • R34_GT to Turbo
      Does RB25DE Neo lower intake work with RB25DET Neo Upper intake manifold?

      By R34_GT to Turbo · Posted

      TD05 or maybe pulsar PSR2867r Gen 2?  id love a garret but it’s quite out the budget for now and I’m not chasing crazy power.    yeh fuel pump haven’t looked into but whatever works, kind of last on my list.    Nistune because it’s simple but Ik it’s a lot of pain especially as I’m auto +t with the whole seperate TCM etc still investigating that. Haltech id love but once budget tight for now atleast.    finally the reason I’m trying for a plenum instead of the stock intake is I already have a standard Intercooler mounted etc. so the ports are on both sides so trying to not have to go over the clutch fan radiator etc. trying to find a good deal return flow if I don’t than this will do for now I guess. btw any ideas with that, apparently some people have to cut blades to reduce it from hitting the Intercooler piping over the radiator ? Thanks 
×
×
  • Create New...