Jump to content
SAU Community

Recommended Posts

ok guys so i been thinking about this 4 a while ..

first i wanted a sub box on the side pannel like you get the fiberglass ones, but wanted it to be wooden didnt like the idea of a flimzy box ...so here are my pics

aretofill.jpg?t=1314015118

the hole to fill ,

started with some dynamat ( didnt car about extra weight) just hate rattles and tiny sound

testfit.jpg?t=1314015119

the disign lay out to get a pattern of how far i wanted it to sit back in there ..

designidea.jpg?t=1314015118after playing around cutting and shutting little bits i took it out to get the outside measurements and transferd it to my mdf sheet and cut it out and tacked it together to see if it fitted back up again DSC_0698.jpg?t=1314015118DSC_0700.jpg?t=1314015118

note the tapper in on the left to fit past the brackets

DSC_0699.jpg?t=1314015118

DSC_0704.jpg?t=1314015119 the reason for the angel :teehee:

DSC_0701.jpg?t=1314015118

fitted up nicely i think had to add it strips under the base to keep it square and sitting flat i tidyd the strips up and screwed em down

( i have finished this box and coved it ill add pics 2mora) its air tight screwd and liquid nailed shut

the amp's will be on a flip down back peace under the rear window so wen its pinned up you will not see the amps or wireing unless its unpined and droped down to keep the boot simple and tidy i havent started that yet but ill update wen its done

also if you dont like well meh :sleep:

Link to comment
https://www.sau.com.au/forums/topic/374900-r34-sub-box/
Share on other sites

FYI .you could have done it and had it behind the panel, there is plenty of airspace and you wouldnt loose any boot. 12" subs fit no cutting of steel

bet that dash is a bugger on sunny days reflecting off the windscreen

but overall a better attempt then some of others in the audio section. IMO

Link to comment
https://www.sau.com.au/forums/topic/374900-r34-sub-box/#findComment-5980996
Share on other sites

its not a gloss paint so it doesnt reflect at all as for box i wanted a sealed wooden box if not i would have just made a pannel like you said and flush mounted it in im not fussed on boot space as its a weekend driver just wanted to get the spare out with out the sub getting in the way

FYI .you could have done it and had it behind the panel, there is plenty of airspace and you wouldnt loose any boot. 12" subs fit no cutting of steel

bet that dash is a bugger on sunny days reflecting off the windscreen

but overall a better attempt then some of others in the audio section. IMO

Link to comment
https://www.sau.com.au/forums/topic/374900-r34-sub-box/#findComment-5981069
Share on other sites

yer the old guy who had it befor me didnt really look after it lol was his work car befor i saved it :closedeyes: i was thinking of wrapping the platic around the arm rest to the gear shift in carbonfiber not sure could look crap with the paint

Link to comment
https://www.sau.com.au/forums/topic/374900-r34-sub-box/#findComment-5982132
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • It says 300ZX, does that make it an Aus delivered car? Funny how back in the day I just couldn't care less about Z32's and these days I am just in love with them. Back when Nissan was into pushing the envelope. 🤣
    • Hi guys, just after some guidance with an R34 sunroof that has stopped working correctly. It still opens and closes perfectly fine, but it no longer tilts/vents up or down. As a result, the rear of the glass now sags a bit as it drops down slightly in order to retract into the roof, but now it can't pop upwards into a flush position. I’ve probed the pins on the back of the switch connector with a multimeter and it seems like both switches (for open/close and tilt/vent) still work correctly. Any ideas on what it could be, or where I should even start in terms of diagnosing? I'm sure someone's had this issue before but I haven't been able to find anything online relating to this specific issue, most of the issues are with the seals leaking or the motor failing entirely. Thanks in advance!
    • Do you have some data like fuel pressure? It's really hard to say if you're still fighting a fuel system issue at this point. Could be something weird like the FPCM dipping out.
    • Yeah in that case, pulling the dent out. Event a very slight dent can create a lot of work filler-wise and there is a strong chance the panel won't be the factory shape when you are done (as the dent will result in a new high point created somewhere, then everything is brought up to that new high point... but the panel shouldn't be that high if that makes sense).  So you've filled and primed the panel and it is flat, why would you go back and remove the primer and add more filler? 
    • Something else I have been faffing with while the car was off the road is making the AC work. Assuming the car isn't at a thermal limit the idea of having AC while waiting in line to go on track sounds delightful. I have actually been lugging around the weight of the entire system since 2018 when the RB25NEO went in without it working at all.  The main reason was in the first few events before I got around to re-gassing it the rubber hose that runs under the manifold had the factory heat wrap/sleeve fail resulting in this: ~2 years ago I purchased a complete used R32 AC line set but when I finally went to install it the line i needed was different where the expansion section is I found a local place that was able to replace the rubber section and re-crimp. They also added some modern heat sleeve to the hose Tight fit but fingers crossed this is the last physical piece of the puzzle needed
×
×
  • Create New...