Jump to content
SAU Community

Recommended Posts

Set Of Standard Springs R32 Gtr $150

Rear Sub Frame,diff,control Arms The Lot Suit Gtst $400

Complete Ac/heater/blower Box Behind Dash $250

Complete Brake Set Up Discs/calipers/master Cyl/booster - Gtst $400

Diff Center 4.3 Lsd $200

INSTRUMENT CLUSTER $ 150

Prices Negotiable

Heaps Of Bits And Pieces Lying Around Pm If You Are After Something

Link to comment
https://www.sau.com.au/forums/topic/37498-r32-bits-and-pieces/
Share on other sites

Set Of Standard Springs R32 Gtr $150

Rear Sub Frame,diff,control Arms The Lot Suit Gtst $400

Complete Ac/heater/blower Box Behind Dash $250

Complete Brake Set Up Discs/calipers/master Cyl/booster - Gtst $400

Diff Center 4.3 Lsd $200

INSTRUMENT CLUSTER $ 150

Prices Negotiable

Heaps Of Bits And Pieces Lying Around Pm  If You Are After Something

I'll take the LSD if still available - pls confirm in good order & mechanical lsd (assuming this is a direct fit in an R32GTST), if not will take rear sub-frame, diff etc.

Set Of Standard Springs R32 Gtr $150

Rear Sub Frame,diff,control Arms The Lot Suit Gtst $400

Complete Ac/heater/blower Box Behind Dash $250

Complete Brake Set Up Discs/calipers/master Cyl/booster - Gtst $400

Diff Center 4.3 Lsd $200

INSTRUMENT CLUSTER $ 150

Prices Negotiable

Heaps Of Bits And Pieces Lying Around Pm  If You Are After Something

Hey i was wondering what condition the brakes are in? and it both front and rear brakes??

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
    • Bit difficult to follow. Have a look below and see what the standard R32 layout was like. Note there was a restrictor in place immediately before "turbocharged pressure control solenoid" that, if removed, magically got you 1 bar boost.
    • I might be way off the mark here.. there must be a T junction under the manifold. That takes manifold pressure through a check valve prior to the T, one side splits out to this bleed off orifice, the other straight to the wastegate actuators. 
    • Carrying out some engine due diligence before my first drive in a 260RS that has been in storage for 10+ years, and found two lines that are susposed to be plumbed into the boost control solenoid. One of the lines (the wastegate boost supply line) to actuate the gates, had a bolt in one end blocking it. The other line (main boost signal line) from the very rear of the intake manifold (RB26DETT) and runs up to the boost controller had this pill in the end of it as seen in photos. Other than the obvious (T28 Ceramic turbos might well be cooked)  Can anyone shed any light on if there is any validity at all with this mod, bleeding a constant fixed rate of manifold boost pressure off through this 3mm hole?  Is it deliberate?  Was this a 90s Jap mod done to RB26's? Or has someone just fitted this without any idea of what happens to ceramic T28s if they are not gate controlled?    
×
×
  • Create New...