Jump to content
SAU Community

Bad News Another Dead Skyline !

cameron
 Share

Recommended Posts

cameron Mentor

cameron

Posted
Posted

Hey everyone...

we if you seen my past thread about my brothers car (r33 gtst) and how the engine died well it had a hole in piston number six, tonight we swaped the avc-r boost controller from that car to my other brothers car (r33 gtst) and we took it for a strap.... max boost we put it in was 1bar but it was reading 12psi (due to duty cycle etc) but as we were driving it suddenly cut out and the engine it died.. when we pulled up it started sounds like the car thats already blown up.. white smoke an piston number 6 is full of oil!! so is the spark plug. so we have no idear what has happened here except to question the avc-r.... the same avc-r has blown up 2 rb25det engines (piston number six) ?

could this be a fault in the system ?

what should you surgest we do ?

Thanks,

Cam

Link to comment
https://www.sau.com.au/forums/topic/37527-bad-news-another-dead-skyline/
Share on other sites
calvintys Experienced

calvintys

Posted
Posted

ermm did have another boost gauge apart from looking or reading the out put of the AVC-R.... if the reading is from another boost guage and the reading from the AVCR is the same then there should not be problem with wiring... if you dont have a boost guage then MAY BE you are receiving wrong information..... i always dont trust boost reading from a boost controller...

BigDatto Proficient

BigDatto

Posted
Posted
Hey everyone...

what should you surgest we do ?

Thanks,

Cam

1. Buy a used engine off these forums (MattR has a couple at the right price).

2. install a GTR / Bosch fuel pump

3. Replace fuel filter & plugs at the correct g a p

4. Get the injectors ultrasonically cleaned

5. Get aftermarket engine management

6.Get it tuned by a pro, on a dyno !!!

If it's a stock turbo it won't live very long at 1 bar pressure. Expect it to throw the exhaust wheel into the cat, destroying it, and potentially being spat back into a valve and.... why am I so unlucky....... engine #4...

Educate yourself about your particular vehicle. Then you can modify it -effectively- that's the whole point of these forums.

Stock RB25's just won't take sustained detonation. End of story.

cameron Mentor

cameron

Posted
  • Author
Posted

yeh it might of been running lean... as on the dyno it was running 30:1 afr at 14psi. but it was only running 11-12psi on boost guage and avc-r so it shouldnt have leand too much. but i think cause the avc-r ran propper boost throught it and it was on 12psi at 3000k all the way to redline, and engine couldnt handle it.

some advice get a fuel pump before boosting your car !

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Shizu
      Sheraaz's R34GTT Build

      By Shizu · Posted

      Omg Brake pedal removal.. FML!!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I mean, I can confirm the TPS is at 100%.... I can confirm when we installed the TB and setup the cable that the TB was indeed fully open at max pedal travel.. the same 'curve' (WRT MAP vs MAP) existed with the previous setup/TB/manifold as well... No, we did not do a run with no intake connected. I would love to go back in time to do such a run to rule out the intake. It would have also been good to do a run with the airbox lid off. There's a test there where increased IAT vs more available air could be a positive tradeoff. I remember taking the lid off my R34 Turbo setup back in the day and noticing a monster increase, even if IAT's did go up. Could be similar. Hard to test unless I find a very deserted road. 
    • LaurelPWR
      Forced Performance Hta Turbos

      By LaurelPWR · Posted

      That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • silviaz
      Steps to DIY sanding car back ready for respray....

      By silviaz · Posted

      I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
×
×
  • Create New...