Jump to content
SAU Community

Recommended Posts

So what are the stock skirt & fbars made out of?

The reason I'm asking is I need to repair some cracks. Everyone says to fiberglass it up. But if you use the wrong resin, all that hard work is just going to come off when the road gets a little bumpy.

I know epoxy only sticks to epoxy, and for polyester and vinylester you should their respective resins...

Anyone got any ideas?

Hi!

I do not know much about the resins and that but when I used to get it for our company (we made custom panels) I just told the guys at the fibreglass workshop what we were doing (Kirkside in Perth) and they were really helpful. They even sent their expert over to help us make models of a protoype firbeglass shell for a sportscar.

So the best bet would be to take it to one of these types of workshops, and they will show you what you are after, how to mix it and everything!

This is my opinion anyway, if you want to do it yourself, and learn about it for future reference! :D

The bumper and side skirts are usually made out of a plastic called ABS. There will be some form of branding on the inside of the product confirming this. Just look for the ABS lettering. The plastic is injection moulded and can be repaired using any quality polyester resin two part system(resin and catylist) The trick is to get the oriniginal parts super clean with a good quality acetone. Just remember : no clean, no stick ! Then you need to get the original parts back together and find a way to hold them there then brush a thin coat of catylised polyester resin on the area, wait till it starts to gell . Then apply a layer of fiberglass or another very strong material on the gelling surface ,squeezing or rolling it into place. the let it cure completely. To finish it off mix up some more resin and paint it over the rest of the exposed fiberglass and let cure.

Now If your head hasnt exploded by now from all that info you should be right

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • After using a protractor for an actually accurate assessment of what is required,  and by NOT using my uncalibrated eyeball I worked out I need a 25° silicone bend from the TB ro the MAF, but, my choice was either a 30° or a 23° (23° is a weird spec), so I grabbed the 23° one from Raceworks I also grabbed 1mtr of 3" straight from Just Jap, I needed 350mm, but they only had 300mm, or 1mtr lengths....meh Also ordered a 1/2" hose bulkhead fitting from fleabay, this has a smoothish mushroom looking head (they are designed for below the water line of boats) that will fit inside the bend, the hose bit and threaded bit looks to long, but nothing that a hacksaw cannot fix if required, the hose will then just get jamed on the threaded bit up to the retaining nut Fingers crossed and the unsightly amount of hose clamps will be reduced down to 4 once all the parts arrive 
    • Oil change does not trigger code 21. Code 21 is for coilpacks primary side connection. You can try to clear the code with a battery disconnect, hold down the brake pedal to drain capacitors through the brake lights with the ignition on for 10-15 seconds before you reconnect the battery. I have seen R35 coil conversion permanently cause this code with no ill effects so it might be the resistance it wants to see isn't quite right on one or more coilpacks. Could be inside the ECU, could be the harness, could be a coil. You can test it all if you want or just ignore until the car actually starts misfiring.
    • I forgot you have a Nistune ECU. Use Nistune to do all the tests I mentioned instead of faffing with 30+ year old electrical connectors. You can read MAF volts off that too, there are reference values in the service manual to tell you roughly what it should be in different conditions.
    • No. I think it might be the AFM. Hence the use of the terms "swaptronics", which implies the use of swapping out electronics for the purpose of diagnosis. It's about the only way to prove that a small/niggling/whatever problem with an AFM or a CAS or similar is actually caused by that AFM/CAS/whatever. A known good item swapped in that still gives the same problem is likely to be caused somewhere else. They're all the same. Spraying AFMs with cleaner is an each way bet between cleaning it and f**king it.
    • Oh wow! This might actually work amazingly. Do you know the ratio of the diff? I was told the only thing you need to make sure of is if the front & rear diff ratios are the same. Ours is a 4.083 Thanks!
×
×
  • Create New...