Jump to content
SAU Community

Recommended Posts

Hi everyone, i have a 1999 nissan stagea rs4 rb25det neo 5 speed manual and having some issues! the car idles fine and revs fine when stationary but when i attempt to drive the car it hits fuel cut under any amount of throttle, iv gone over and checked for vacuum leaks everything appears good car is running standard boost it cuts out even before it reaches boost what could be causing this? crank angle sensor? airflow meter? when the car cuts out it doesn't stall just cuts fuel and wont allow me to accelerate doesn't back fire or sound like a misfire any help would be greatly appreciated.

Link to comment
https://www.sau.com.au/forums/topic/376139-possible-fuel-cut/
Share on other sites

If your running FMIC check for leaks, split or dislodged hose etc. Check the AFM connection and give the AFM a good squirt of throttle body cleaner, also do the TB

It sounds like its in limp so could be any of the above. Our C34 N/A went like that and it was the timing belt. The tensioner had seized and laminated the belt which jumped a couple of teeth. This threw the car into Limp.

checked and cleaned everything all intake hose's tight and not leaking still doing it could it be the turbosmart bov im going to chase up a standard bov and try that if that doesn't work would the CAS cause this issue. it will rev fine in neutral with out any issues and idles perfect like there is no leaks only does it when i try and drive. ( Anyone got a standard BOV in Brisbane want to swap or sell for cheap or free ) i cleaned out the fuel filter also seems fine :(

when you say it cuts out do your mean it just feels like its being held back, or the engine literally cuts out for a second? if it just feels like its holding back you could be onto something with the bov, possibly leaking? faulty AFM will cause poor performance as hugh mentioned. if your getting a full engine cut it could be a faulty map sensor causing the ecu to think you've over boosted.

i'm in brissy and have a stock bov your welcome to have (for free) if you want to come and get it. i've also got a consult cable and software i can hook up to the ecu and have a look at what all the sensors are doing. let me know if your keen, i'm in Cannon Hill (south side).

Edited by QWK32

QWK32 that would be great if you could hook up the software and find out for me. what i mean by cutting out, it feels as though it just stops fuel getting to the motor the car will start to accelerate then its like some one has cut the throttle cable just cuts out before boost is even reached but doesn't stall and if i put the clutch in i can still rev it and release the clutch and i am able to limp it home providing i don't give it to much throttle? im located in Kenmore (west side) the car does not drive so i wont be able to come to you?

  • 2 weeks later...
  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
    • I don't get in here much anymore but I can help you with this.   The hole is a vent (air relief) for the brake proportioning valve, which is built into the master cylinder.    The bad news is that if brake fluid is leaking from that hole then it's getting past the proportioning valve seals.   The really bad news is that no spare parts are available for the proportioning valve either from Nissan or after market.     It's a bit of a PITA getting the proportioning valve out of the master cylinder body anyway but, fortunately, leaks from that area are rare in my experience. BTW, if those are copper (as such) brake lines you should get rid of them.    Bundy (steel) tube is a far better choice (and legal  in Australia - if that's where you are).
×
×
  • Create New...