Jump to content
SAU Community

Recommended Posts

Hey guys, get some wheel nuts asap for cheap!!!!

http://fitmentfactory.bigcartel.com/

My friend is having a sale, $120 for Rays Dura Nuts!

Postage is $10 too!!!! awesome deal,

They sell on other sites for $275 + postage

http://justjap.com/s...&cat=262&page=3

Cobey.

Edited by Cobey
Link to comment
https://www.sau.com.au/forums/topic/376716-get-some-wheel-nuts/
Share on other sites

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

Speaking of wheel nuts, anyone know of quality black locking wheel nuts?

Sorry, my mistake. Drop down list shows price for 5 x 50mm nuts as $120, just as Cobey said.

They also come in black & the 7 sided one acts as a lock nut (unless the thief happens to have the correct tool).

Sorry Cobey, not trying to ruin your thread but the public needs to know there are plenty of fake ones currently in circulation that look identical...there is even a forum member selling these in the GB section and plenty on Ebay at similar prices.

Check here:

http://www.ontherunmotorsports.com/index.php?option=com_content&view=article&id=203:rays-beware-of-fake-rays-dura-nuts&catid=36:wheels&Itemid=70

I hope your mate is selling the genuine ones otherwise I would not touch cheap china replica nuts to hold on to my $4k wheels... :thumbsup:

Yeah, but that means buying a full set of nuts - I just want 4 lock nuts - in black.

I already have a complete set of nismo wheel nuts. I don't need or want Rays ones. (And the nismo ones act as a 'sorta' lock nut already being 7-sided - on all nuts, not just four). Really, I'm just after extra protection - 7-sided isn't enough in my opinion.

Just got mine, there's no fillings in the thread, rays looks to be stamped right, but there was no sticker on the box... Was told their legit, yet again. As I said looks to be legit, and cheap. So up to you guys, ps, light as f**k. And I can't upload pics as I'm on my iPhone.

Hard to tell, some things make it look legit, others don't (no sticker on box.... i'm unsure but here's a photo the quality looks to be very high if its a fake, you be the judge.

I've got mine, and i'm happy. measure all tapers and the aren't unstable, no excess metal anywhere, all cuts clean? go figure.

img13811.jpg

img13821.jpg

I personally wouldn't spend $275 but I spent $120 and ordered a set because it was on sale. Not only are they lightweight but they're strong. Also the paint doesn't scratch off like some other cheaper aftermarket brands and since I own a $20,000 car and $1500 wheels, I wanna be assured that my lug nuts will hold and won't warp.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...