Jump to content
SAU Community

Boost Gauge .. Where Did You Put It?

Ezekiel86

By Ezekiel86,
in Four Door Family & Wagoneers

 Share

Recommended Posts

  • Replies 56
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Posted Images

BigDirtyJase Experienced

BigDirtyJase

Posted
Posted

Thats how I wanted it but I think we have a different metal brace to other ppl. Everything screws in the middle and locks into the little slots (red circles) but the climate control mounts further to the bottom than center (top two red circles).

Also the climate control is slightly wider at the front and only seems to fit where the brace is shallower (blue line)

If you find a way it fits without cutting and drilling I'd like to know how

post-78650-0-24142600-1315913055_thumb.jpg

I wonder if the climate control unit and/or the bracket are different between the V (auto) and the S (manual). The S has the factory three gauges up the top and then the climate control in the middle (sometimes it's the other way round)..

post-34764-0-53089400-1316871909_thumb.jpg

As you can see in the photo...I wonder if our manual friends on here can tell us is there a difference in the climate control unit or the bracket because like you, I don't want to do any cutting or trimming of he bracket

SatchiThaStagea Community Regular

SatchiThaStagea

Posted
Posted

My pic is of an auto not sure if it gives enough of an idea where things sit.

I've already outlined the main issues I can see. When I tried to put the climate control else where it just didnt want to fit.pinch.gif

  • 1 month later...
Marshstag Collaborator

Marshstag

Posted
Posted

Thats how I wanted it but I think we have a different metal brace to other ppl. Everything screws in the middle and locks into the little slots (red circles) but the climate control mounts further to the bottom than center (top two red circles).

Also the climate control is slightly wider at the front and only seems to fit where the brace is shallower (blue line)

If you find a way it fits without cutting and drilling I'd like to know how

post-78650-0-24142600-1315913055_thumb.jpg

Does anyone know if you the brackets pictured below, would be suitable for the gauges/climate/stereo order?

daf680ss-img600x450-1312181089nrcy0y21859.jpg

Marshstag Collaborator

Marshstag

Posted
Posted

They look the same as my rs4s ones.

Awesome, thanks for that mate. I've purchased them through Import Monster so they should be here in a few weeks... fingers crossed that they will do the job. :thumbsup:

BigDirtyJase Experienced

BigDirtyJase

Posted
Posted

Awesome, thanks for that mate. I've purchased them through Import Monster so they should be here in a few weeks... fingers crossed that they will do the job. :thumbsup:

whereabouts in Import Monster did you find it??

Marshstag Collaborator

Marshstag

Posted
Posted (edited)

whereabouts in Import Monster did you find it??

I think I searched for ステージア(Stagea in Japanese) under the Car Audio category. I did a lot of trawling, things seems to be listed all over the place :P

Edited by Marshstag

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • pacman_1219
      Blue/grey smoke after idle

      By pacman_1219 · Posted

      Even with the piston at TDC there was room for it to drop, but I don't think it can drop fully into the cylinder, the problem you have is that you need something pushing against the valve to hold it up so you have enough room to put the new stem seal on and the spring etc.  I used compressed air only because putting rope in the cylinder seemed a bit risky to me, I know people have done it countless times before like this. Overall it's a pain in the ass job. Honestly you'd probably be better off taking the head off because the risk of dropping something in the engine and the finicky-ness of it all is very stressful. If you are going to attempt it though i 10000% recommend a 36050 valve spring/keeper tool. I had both the traditional lever type and after doing 1 cylinder it was absolute pain to get those valve keepers in place, even with 2 people. That 36050 is amazing, you do have to push hard to get them in place but it works perfectly almost every time. Back to my actual issue I think my engine is just tired and old and the rings have gone bad. The comp numbers (cold, no oil) were: Cyl 1 -129psi Cyl 2 - 133psi Cyl 3 - 138psi Cyl 4 - 137psi Cyl 5 - 157psi Cyl 6 - 142psi   Cylinder 5 and 6 having the most carbon on them.
    • MBS206
      R33 Fuel Pump & Brakes after alarm swap

      By MBS206 · Posted

      Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • GTSBoy
      R33 Fuel Pump & Brakes after alarm swap

      By GTSBoy · Posted

      Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • GTSBoy
      After market rear camber arm adjustment

      By GTSBoy · Posted

      Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Jarsky
      R33 Fuel Pump & Brakes after alarm swap

      By Jarsky · Posted

      Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
×
×
  • Create New...