Jump to content
SAU Community

Getting Ready For Dyno This Week.

lilcrash

By lilcrash,
in Four Door Family & Wagoneers

 Share

Recommended Posts

lilcrash Veteran

lilcrash

Posted
  • Author
Posted (edited)

That isn't the sole reason.

Ps. I only damaged one and gave up trying, they killed one then decided oh we don't have the tools to do this.

Edited by lilcrash
Tangles Grand Master

Tangles

Posted
Posted

no Multi-grip? sounds like a poor excuse for a job they obviously didnt want to be bothered with.

Best of luck with the tune.

Bit of a warning tho, youve been driving without a tune since the last round of mods. Rb25's are notorious for damaging ringlands. your oil useage could refelct the start of some piston damage. I found out the hard way (back on April 11th) and am still without any mode of transport .... :/

lilcrash Veteran

lilcrash

Posted
  • Author
Posted (edited)

yeah it sounded like they didnt want to do it, the moment they started working on it and decided they were not gonna tune it everyone went home as my car was the only work for the day.

i'm actually concerned that something happened down there and thats why they didnt touch it because since i've picked it up it hasn't been running too well, i'm hoping its just the heat but i've had dodgy workshops do stupid things before.

i think i read rb enignes dont like detonation, im guessing this is what your talking about. i was hoping to get it all tuned by now but it appears that everyone is either too busy or just doesn't want to touch nistune anymore. oh well i will pull the shaft out tomorrow and im sure that hi power racing and ben phillips would love to make some money doing the final tweaks on my ecu.

Edited by lilcrash
lilcrash Veteran

lilcrash

Posted
  • Author
Posted (edited)

Ok update, 15-20 minutes and the bolts are out, probably 10 minutes of that was trying to rolll the car around to get the last 2 bolts at the bottom, now how do I get the shaft out???

Edited by lilcrash

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      boost source Size Garrett gt28 gen2

      By TurboTapin · Posted

      You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • QB6SAGR
      Battle of the broken skylines

      By QB6SAGR · Posted

      Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • cosline
      R32 gtr transmission strength, billet plate

      By cosline · Posted

      Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
    • Rezz
      Spotted on the street....

      By Rezz · Posted

      Saw this replica police car based on a Mitsubishi Starion XX parked next to a 'police box' (it's literally a box) in Hirohata, Himeji City in Hyogo prefecture the other day. It's owned by Morii-san who is a local Mitsubishi Starion enthusiast. According to a local radio station blog post, he always wanted to make a police car himself based on ones he saw in his favourite Manga comics.  As it's illegal to modify a car to look like a police car and drive on the road, Morii-san tried many times to get permission from Aboshi police station headquarters nearby. They refused initially by after they got tired of that they granted him permission. However, the car can only be displayed on private property and obviously can't be registered as long as the police livery is present. The car was completed at a cost of 1.5 million yen (US$ 10,000) in addition to the car cost. A location was chosen outside Hirohata Police box where the car can easily been seen from the street. Morii-san has two other Starion road cars, both widebody GSR-VRs.
×
×
  • Create New...