Jump to content
SAU Community

Boost on stock GTR

marchGTR

By marchGTR,
in Engines & Forced Induction

 Share

Recommended Posts

marchGTR Collaborator

marchGTR

Posted
Posted

Hi all,

I have just bought myself a bog stock R33 GTR(purple!) and was wondering if its OK to remove the boost restrictor even with a stock exhaust?

I will get a new exhaust in the future, but tempted to remove the restrictor in the meantime??

I have looked through previous threads but havent found the answer to this question

Link to comment
https://www.sau.com.au/forums/topic/37776-boost-on-stock-gtr/
Share on other sites
400kwgtr Rising Star

400kwgtr

Posted
Posted

removing the restrictor will give you about 15psi, which is around double the standard boost. Doing this with a standard exhaust is fine, you wont get as much power as you would with a 3 inch system. It will be a big improvement and the car will kick ass. To be safe you should get a new boost guage and monitor the exact boost the car is producing or you might end up with a little ceramic turbo wheel stuck in your cat converter...

marchGTR Collaborator

marchGTR

Posted
  • Author
Posted
removing the restrictor will give you about 15psi, which is around double the standard boost. Doing this with a standard exhaust is fine, you wont get as much power as you would with a 3 inch system. It will be a big improvement and the car will kick ass. To be safe you should get a new boost guage and monitor the exact boost the car is producing or you might end up with a little ceramic turbo wheel stuck in your cat converter...

Thanks for your advice..ill get a boost guage and take it from there.

  • 1 month later...
Ronin 09 Grand Master

Ronin 09

Posted
Posted

Sorry to dig up a dead thread, but I have just noticed that my R32 gtr std boost gauge goes over the +7 std reading when boosting.

It has a cat-back (soon to be full system), and I can't feel the boost restrictor around the yellow dotted line (removed?)...

My question is, is this safe turbo wise, and, what equivalent PSI or bar should I expect? I will try and hook into a boost gauge this weekend...

RBVS Community Regular

RBVS

Posted
Posted

when you say remove the restrictor what is that in relation two. If its a restrictor in the vacum line to the actulator removing it would make you run less boost, as more air is going to hit the actulator sooner thier for opening the wast gate sooner??

or is there some kind of ecu restrictor?

Unless the restrictor is in line with T peace and soliniode, then removing it would allow the soliniod to bleed more air, in turn raising the boost. Can somone clear this up for me?

Ronin 09 Grand Master

Ronin 09

Posted
Posted

I'm talking about the brass restrictor in a vac line on the driver's side of the car - it is highlighted by a yellow line around the vac line...

anyone want to tell me what is the PSI if the factory gauge is reading over +7 ??

dangerous or not?

Ronin 09 Grand Master

Ronin 09

Posted
Posted

Ooh crap - they are stockers - at least thats what I thought.

I bought it (apparently) stock, only change is I've bolted up a cat back.

I'm sure the restrictor is not there - I'll go take a pic in a sec...

OK i can't feel any brass thingy in the vac line around the yellow line, but the buldge between the clamp band and the yellow line - is this where the restrictor is?

Cheers

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...